Performances of ϕ139.7 mm×7.72 mm J55 Low Pressure Gas-Tight Threaded Casing Joints
摘 要
对自行设计的ϕ139.7 mm×7.72 mm J55低压气密封螺纹套管接头进行了上卸扣、热循环气密封、弯曲条件下气体内压拉伸、拉伸至失效、加内压至失效等试验。结果表明:该接头的抗粘扣性能良好;135℃,35 MPa条件下的气密封性能和低压30 MPa、弯曲狗腿度10°/(30 m)、拉伸载荷为80%材料名义屈服强度条件下的气密封性能均合格;接头的泄漏失效内压和抗拉强度均远高于标准技术要求。
Abstract
Making up and breaking out tests, thermal cycle gas-tight tests, internal pressure and tension tests under bending condition, tension to failure tests, and internal pressure to failure tests were carried out to ϕ139.7 mm×7.72 mm J55 low pressure gas-tight casing joint samples. The results show that the anti-gluing property of the joints was good, the sealing capability was qualified both under the condition of the temperature of 135℃ and the pressure of 35 MPa and under the condition of the pressure of 30 MPa, the bending dogleg angle of 10°/(30 m) and the tension load of 80% nominal yield strength. The leakage failure internal pressure and the tension strength of the joints were all much higher than those of the standard technical requirements.
中图分类号 TE931.2 DOI 10.11973/lhjy-wl201708008
所属栏目 试验与研究
基金项目
收稿日期 2015/6/10
修改稿日期
网络出版日期
作者单位点击查看
备注李玲霞(1984-),女,高级工程师,主要从事油井管产品开发研究,daxue-xiaocao@163.com
引用该论文: LI Lingxia,DENG Xuyan,MU Zengli. Performances of ϕ139.7 mm×7.72 mm J55 Low Pressure Gas-Tight Threaded Casing Joints[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2017, 53(8): 573~576
李玲霞,邓叙燕,穆增利. ϕ139.7 mm×7.72 mm J55低压气密封螺纹套管接头性能[J]. 理化检验-物理分册, 2017, 53(8): 573~576
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】吕拴录,滕学清,杨成新,等.某井套管柱泄漏原因分析[J].理化检验-物理分册,2013,49(5):334-338.
【2】刘建勋,吕拴录,高运宗,等.塔里木油田非API油、套管失效分析及预防[J].理化检验-物理分册,2013,49(6):416-418.
【3】张毅,袁鹏斌,高连新.油井管失效分析[M].北京:石油工业出版社,2015.
【4】高连新,张毅.管柱设计与油井管选用[M].北京:石油工业出版社,2013.
【5】高连新,史交齐.油套管特殊螺纹接头连接技术的研究现状及展望[J].石油矿场机械,2008,37(2):15-19.
【6】付彧,齐国权,卫遵义,等.特殊螺纹油套管设计及国内产品现状[J].石油矿场机械,2012,41(10):72-76.
【7】蔡晓闻,高连新.我国油套管特殊螺纹接头的发展现状[J].焊管,2008,31(4):41-44.
【8】宫翔,李玲霞,穆增利.基于ABAQUS改进型圆螺纹套管的受力分析[J].机械工程师,2015(11):199-201.
【2】刘建勋,吕拴录,高运宗,等.塔里木油田非API油、套管失效分析及预防[J].理化检验-物理分册,2013,49(6):416-418.
【3】张毅,袁鹏斌,高连新.油井管失效分析[M].北京:石油工业出版社,2015.
【4】高连新,张毅.管柱设计与油井管选用[M].北京:石油工业出版社,2013.
【5】高连新,史交齐.油套管特殊螺纹接头连接技术的研究现状及展望[J].石油矿场机械,2008,37(2):15-19.
【6】付彧,齐国权,卫遵义,等.特殊螺纹油套管设计及国内产品现状[J].石油矿场机械,2012,41(10):72-76.
【7】蔡晓闻,高连新.我国油套管特殊螺纹接头的发展现状[J].焊管,2008,31(4):41-44.
【8】宫翔,李玲霞,穆增利.基于ABAQUS改进型圆螺纹套管的受力分析[J].机械工程师,2015(11):199-201.
相关信息
标题 | 相关频次 | |
声发射技术在热障涂层失效机理研究中的应用 | 2 | |
630 ℃长时时效对G112钢组织和力学性能的影响 | 1 | |
700 ℃长时时效对LF2合金组织和高温拉伸性能的影响 | 1 | |
φ177.8 mm偏梯形螺纹套管粘扣原因分析 | 1 | |
铬镍奥氏体不锈钢焊缝铁素体含量的测定 | 1 | |
某油井特殊螺纹接头油管粘扣原因分析 | 1 | |
钻杆接头粘扣原因分析 | 1 |