Reason for Edge Cracking of Cold-Rolled 55Mn Strip Steel and the Cold-rolling Control Measures
摘 要
采用光学显微镜、扫描电镜及能谱仪等分析了55Mn冷轧带钢边裂缺陷的形成原因,提出了优化的冷轧控制措施并进行了验证。结果表明:因铸坯本身有微小裂纹,致使其在热轧加热过程中产生局部脱碳是造成冷轧带钢边裂的直接原因;通过将拉矫机的延伸率参数设定为正常时的50%,酸洗液质量浓度较正常的增大5%~10%,酸洗速度降至正常时的70%,前两个机架的负荷分配设定为总压下量的70%以上,机架间的微拉应力控制在正常时的70%以内,能够有效控制此边裂现象的出现。
Abstract
The cause of the edge cracking of cold-rolled 55Mn strip steel was analyzed by means of the optical microscopy, scanning electron microscopy, energy dispersive spectroscopy and so on, and the optimal control measures of cold-rolling were proposed and confirmed. The results show that the local decarburization produced in the hot-rolling process, due to the microcracks in the slab, was the direct cause of the edge cracking of cold-rolled strip steel. This edge cracking can be controlled effectively by the measures of setting the elongation of straightening to 50% of the normal elongation, increasing the mass concentration of pickling solution by 5%-10% of the normal concentration, slowing down the pickling speed to 70% of the normal speed, setting the load distribution of the first two racks to 70% of the total reduction and controlling the micro tensile stress between racks less than 70% of the normal one.
中图分类号 TG335.3 DOI 10.11973/jxgccl201708007
所属栏目 新材料 新工艺
基金项目 唐山市科技创新团队培养计划资助项目(15130202C)
收稿日期 2016/8/6
修改稿日期 2017/6/25
网络出版日期
作者单位点击查看
备注陈连生(1968-),男,河北唐山人,教授,博士
引用该论文: CHEN Liansheng,LI Yue,SONG Jinying,ZHENG Xiaoping,TIAN Yaqiang,LI Guanglin. Reason for Edge Cracking of Cold-Rolled 55Mn Strip Steel and the Cold-rolling Control Measures[J]. Materials for mechancial engineering, 2017, 41(8): 31~34
陈连生,李跃,宋进英,郑小平,田亚强,李广林. 55Mn冷轧带钢边裂的产生原因及冷轧控制措施[J]. 机械工程材料, 2017, 41(8): 31~34
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】车彦民, 朱涛, 章华明,等. CSP板卷及冷轧镀锌板表面缺陷分析[J]. 钢铁, 2006, 41(2):63-66.
【2】高玉明, 隋晓红. 冷轧低碳钢薄板边裂原因分析[J]. 机械工程材料, 2011,35(5):83-85.
【3】石虎珍. 薄板坯连铸连轧无取向硅钢的裂纹缺陷分析[D]. 沈阳:东北大学, 2008.
【4】王畅, 于洋, 王林,等. 冷硬卷边裂典型缺陷的成因分析[J]. 轧钢, 2016(1):37-40.
【5】董双鹏, 宋进英, 陈业熊,等. 冷轧钢板表面缺陷的种类及形成原因[J]. 机械工程材料, 2012,36(7):100-104.
【6】ERVASTI E, STÅHLBERG U. Transversal cracks and their behaviour in the hot rolling of steel slabs[J]. Journal of Materials Processing Technology, 2000, 101(1):312-321.
【7】LACHMUND H, SCHWINN V, JUNGBLUT H A. Heavy plate production:Demand on hydrogen control[J]. Ironmaking & Steelmaking, 2000, 27(5):381-386.
【8】孙权, 闫玉曦, 陈建钧,等. 基于GTN损伤模型对含边部缺陷硅钢薄板冷轧时边裂的预测[J]. 机械工程材料, 2013,37(1):93-97.
【9】宋进英, 董双鹏, 陈业雄, 等. 钢板边裂缺陷原因分析及整改措施研究[J]. 钢铁钒钛, 2012, 33(2):87-92.
【10】高新军, 张小欢, 李阳,等. SPHC钢热轧板卷破边成因及防治措施[J]. 钢铁, 2011, 46(6):96-99.
【11】赵培林, 孙新军, 雍岐龙, 等. 超高强度热轧钢板冷冲压开裂原因及分析[J]. 金属热处理, 2012, 37(7):122-126.
【12】崔约贤, 王长利. 金属断口分析[M]. 哈尔滨:哈尔滨工业大学出版社, 1998.
【13】刘宗昌. 珠光体转变理论研究的新进展[J]. 金属热处理, 2008, 33(4):1-8.
【14】崔忠圻, 谭耀春. 金属学与热处理[M]. 北京:机械工业出版社, 2010.
【2】高玉明, 隋晓红. 冷轧低碳钢薄板边裂原因分析[J]. 机械工程材料, 2011,35(5):83-85.
【3】石虎珍. 薄板坯连铸连轧无取向硅钢的裂纹缺陷分析[D]. 沈阳:东北大学, 2008.
【4】王畅, 于洋, 王林,等. 冷硬卷边裂典型缺陷的成因分析[J]. 轧钢, 2016(1):37-40.
【5】董双鹏, 宋进英, 陈业熊,等. 冷轧钢板表面缺陷的种类及形成原因[J]. 机械工程材料, 2012,36(7):100-104.
【6】ERVASTI E, STÅHLBERG U. Transversal cracks and their behaviour in the hot rolling of steel slabs[J]. Journal of Materials Processing Technology, 2000, 101(1):312-321.
【7】LACHMUND H, SCHWINN V, JUNGBLUT H A. Heavy plate production:Demand on hydrogen control[J]. Ironmaking & Steelmaking, 2000, 27(5):381-386.
【8】孙权, 闫玉曦, 陈建钧,等. 基于GTN损伤模型对含边部缺陷硅钢薄板冷轧时边裂的预测[J]. 机械工程材料, 2013,37(1):93-97.
【9】宋进英, 董双鹏, 陈业雄, 等. 钢板边裂缺陷原因分析及整改措施研究[J]. 钢铁钒钛, 2012, 33(2):87-92.
【10】高新军, 张小欢, 李阳,等. SPHC钢热轧板卷破边成因及防治措施[J]. 钢铁, 2011, 46(6):96-99.
【11】赵培林, 孙新军, 雍岐龙, 等. 超高强度热轧钢板冷冲压开裂原因及分析[J]. 金属热处理, 2012, 37(7):122-126.
【12】崔约贤, 王长利. 金属断口分析[M]. 哈尔滨:哈尔滨工业大学出版社, 1998.
【13】刘宗昌. 珠光体转变理论研究的新进展[J]. 金属热处理, 2008, 33(4):1-8.
【14】崔忠圻, 谭耀春. 金属学与热处理[M]. 北京:机械工业出版社, 2010.
相关信息