Abnormal Color Analysis of Anodized Oxidation Film of a 2D70 Aluminum Alloy Cylindrical Part
摘 要
针对某2D70铝合金筒形件表面阳极氧化膜颜色异常发白的缺陷,利用光学显微镜、扫描电子显微镜、透射电子显微镜和电导率仪等研究了基体及氧化膜的显微组织、微区成分、析出相和电导率,分析了其颜色异常发白的原因。结果表明:该筒形件部分区域在时效过程中因温度过高而导致析出相异常长大,在阳极化过程中粗大析出相使该区域内电流密度发生波动,导致膜层致密程度与周围正常区域的差异较大而引起反光能力不同,致使颜色异常发白;可在进行时效等热处理时采取悬挂等措施以避免局部温度过高。
Abstract
Aiming at the abnormal white color defect of anodized oxidation film on the surface of a 2D70 aluminum alloy cylinderical part, the microstructure,micro-area composition, precipitation and the conductivity of the matrix and the oxidation film were studied by the optical microscope, scanning electron microscope, transmission electron microscope and conductivity meter and the reason for the abnormal white color was analyzed. The results show that the precipitations in some areas of the cylindrical part grew abnormally due to the high temperature during the ageing process. These coarse precipitations resulted in the current density fluctuation in these areas during the anodized oxidation process, leading to the different relative density of the film from that of the surrounding normal areas. The different relative density caused the different ability of the reflecting power, leading to the abnormal white color. Some measures such as hanging the parts during the ageing treatment can be adopted to avoid the partially high temperature.
中图分类号 TB31 DOI 10.11973/jxgccl201708023
所属栏目 失效分析
基金项目 辽宁省教育厅基础科研一般项目(L2014071)
收稿日期 2016/7/13
修改稿日期 2017/6/25
网络出版日期
作者单位点击查看
备注张利(1978-),男,辽宁凌源人,工程师,博士
引用该论文: ZHANG Li,DUAN Guosheng,WU Baolin. Abnormal Color Analysis of Anodized Oxidation Film of a 2D70 Aluminum Alloy Cylindrical Part[J]. Materials for mechancial engineering, 2017, 41(8): 102~105
张利,段国升,武保林. 某2D70铝合金筒形件阳极氧化膜颜色异常分析[J]. 机械工程材料, 2017, 41(8): 102~105
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】朱祖芳.铝合金阳极氧化与表面技术[M].北京:化学工业出版社, 2004.
【2】朱祖芳.铝合金阳极氧化的常见缺陷[J]. 轻合金加工技术, 1998, 26(4):29-32.
【3】杨景伟,赵永岗,孙杰,等.铝合金铬酸阳极氧化后表面缺陷分析[J]. 表面技术, 2014, 43(2):72-74.
【4】李宗勇,王小勇. 铝合金阳极氧化膜层颜色均匀性问题[J]. 腐蚀与防护, 2004, 25(9):397-399.
【5】张锐.浅谈铝及铝合金阳极氧化染黑色技术[J]. 涂装与电镀, 2008, 6(2):27-28.
【6】何建平,袁庆铭. 7075铝合金阳极氧化膜的结构和性能研究[J]. 机械工程材料, 2003, 27(9):5-8.
【7】杨守杰,黄敏, 朱娜,等. 2D70铝合金热稳定性研究[J]. 航空材料学报, 2003, 23(z1):73-77.
【2】朱祖芳.铝合金阳极氧化的常见缺陷[J]. 轻合金加工技术, 1998, 26(4):29-32.
【3】杨景伟,赵永岗,孙杰,等.铝合金铬酸阳极氧化后表面缺陷分析[J]. 表面技术, 2014, 43(2):72-74.
【4】李宗勇,王小勇. 铝合金阳极氧化膜层颜色均匀性问题[J]. 腐蚀与防护, 2004, 25(9):397-399.
【5】张锐.浅谈铝及铝合金阳极氧化染黑色技术[J]. 涂装与电镀, 2008, 6(2):27-28.
【6】何建平,袁庆铭. 7075铝合金阳极氧化膜的结构和性能研究[J]. 机械工程材料, 2003, 27(9):5-8.
【7】杨守杰,黄敏, 朱娜,等. 2D70铝合金热稳定性研究[J]. 航空材料学报, 2003, 23(z1):73-77.
相关信息