Determination of Diffusible Hydrogen Content in Deposited Metals
摘 要
依据GB/T 3965-2012分别采用水银法和热导法对熔敷金属中的扩散氢含量进行了测定,对两种方法的测定结果进行了比较,并运用数理统计方法确定了两种方法测定结果之间的函数关系。结果表明:该两种方法均具有较高的测定精度,且两种方法的测定结果很相近,热导法的略小于水银法的;两种方法熔敷金属扩散氢含量测定结果的线性回归方程为y=1.019 5x-0.189 8,与y=x非常接近。
Abstract
According to GB/T 3965-2012, the diffusible hydrogen content in deposited metals were determined by mercury method and thermal conductivity method respectively. The determination results by the two methods were compared, and the functional relationship between the determination results by the two methods was determined by using mathematical statistics method. The results show that both the two methods had high determination precision with similar determination results, and the determination results measured by thermal conductivity method were slightly smaller than those measured by mercury method. The linear regression equation between the determination results of diffusible hydrogen content in deposited metals measured by the two methods was y=1.019 5x-0.189 8 which was very close to y=x.
中图分类号 TG406 DOI 10.11973/lhjy-wl201712006
所属栏目 试验与研究
基金项目
收稿日期 2017/2/20
修改稿日期
网络出版日期
作者单位点击查看
备注宗杰(1980-),男,工程师,学士,主要从事实验室认可体系管理和理化检测研究工作,593946006@qq.com
引用该论文: ZONG Jie,JIANG Zhiqiang. Determination of Diffusible Hydrogen Content in Deposited Metals[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2017, 53(12): 879~881
宗杰,蒋志强. 熔敷金属中扩散氢含量的测定[J]. 理化检验-物理分册, 2017, 53(12): 879~881
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】ISO 3690:2012 Welding and allied processes-Determination of hydrogen content in arcweld metal[S].
【2】GB/T 3965-2012 熔敷金属中扩散氢测定方法[S].
【3】AWS A4.3-1993(R2006) Standard methods for determination of the diffusible hydrogen content of martensitic, bainitic, and ferritic steel weld metal produced by arc welding[S].
【4】马青军,方乃文,宋北,等. 4种扩散氢测定方法的数据对比及稳定性探究[J]. 焊接,2016(8):50-54.
【5】宋北,马青军,杨子佳,等. 熔敷金属中扩散氢测试方法的研究进展[J]. 机械制造文摘(焊接分册),2016(1):41-43.
【6】冯涛. 两种常用扩散氢含量测定方法的比较[J]. 中国高新技术企业,2008(18):88,92.
【7】蔡俊,田海成,张少健,等. 屈服强度460 MPa级药芯焊丝扩散氢含量研究[J]. 焊接技术,2016,45(8):60-62.
【8】王怀龙,钱伟方,刘硕. 埋弧焊剂含水率与熔敷金属扩散氢关系研究[J]. 宝钢技术,2016(4):34-37.
【2】GB/T 3965-2012 熔敷金属中扩散氢测定方法[S].
【3】AWS A4.3-1993(R2006) Standard methods for determination of the diffusible hydrogen content of martensitic, bainitic, and ferritic steel weld metal produced by arc welding[S].
【4】马青军,方乃文,宋北,等. 4种扩散氢测定方法的数据对比及稳定性探究[J]. 焊接,2016(8):50-54.
【5】宋北,马青军,杨子佳,等. 熔敷金属中扩散氢测试方法的研究进展[J]. 机械制造文摘(焊接分册),2016(1):41-43.
【6】冯涛. 两种常用扩散氢含量测定方法的比较[J]. 中国高新技术企业,2008(18):88,92.
【7】蔡俊,田海成,张少健,等. 屈服强度460 MPa级药芯焊丝扩散氢含量研究[J]. 焊接技术,2016,45(8):60-62.
【8】王怀龙,钱伟方,刘硕. 埋弧焊剂含水率与熔敷金属扩散氢关系研究[J]. 宝钢技术,2016(4):34-37.
相关信息