胜利油田某油井盲管腐蚀穿孔的原因
Corrosion Perforation Reason of a Blind Tube in Shengli Oilfield
摘 要
采用直读光谱仪、金相显微镜、扫描电子显微镜（SEM）和X射线衍射（XRD）等对腐蚀穿孔管段宏观形貌、腐蚀产物成分及物相组成等进行了观察和分析，并结合盲管现场服役工况调研，研究了胜利油田某油井盲管发生腐蚀穿孔的原因。结果表明：在现场腐蚀工况条件下，盲管主要发生CO2腐蚀，而处于射孔范围的盲管管段，容易受流体冲刷导致腐蚀产物破损及脱落，引起局部腐蚀，造成盲管腐蚀穿孔失效。
失效分析
CO2腐蚀
冲刷腐蚀
N80 blind tube
failure analysis
CO2 corrosion
erosion corrosion
Abstract
The macroscopic morphology, composition and phase composition of corrosion products of a failed blind tube in Shengli oilfield were observed and analyzed by direct reading spectrometer, metallographic microscopy, scanning electron microscopy (SEM) and X-ray diffraction (XRD). Combined with the service condition of the blind tube, the corrosion and perforation causes of the blind tube were studied. The results showed that CO2 corrosion mainly occurred in the blind tube. Besides, as the blind tube section was in the perforating range, corrosion products were easily damaged and fallen off by fluid, which caused localized corrosion and corrosion perforation finally.
中图分类号 TG172 DOI 10.11973/fsyfh-201803016
所属栏目 失效分析
基金项目
收稿日期 2016/12/15
修改稿日期
网络出版日期
作者单位点击查看
引用该论文: WEI Min. Corrosion Perforation Reason of a Blind Tube in Shengli Oilfield[J]. Corrosion & Protection, 2018, 39(3): 239
共有人对该论文发表了看法，其中：
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】蔡峰,柳伟,樊学华,等. 流体喷射条件下金属材料冲刷腐蚀的研究进展[J]. 摩擦学学报,2011,31(5):521-527.
【2】代真,沈士明,丁国铨. 金属在固液两相流体中的冲刷腐蚀及其防护[J]. 腐蚀与防护,2007,28(2):86-89.
【3】SCHMITT G,GUDDE T,STROBEL-EFFERTZ E. Fracture mechanical properties of CO2 corrosion product scales and their relation to localized corrosion[C]//Corrosion/1996. Houston,Texas:NACE,1996:96009.
【4】KWOK C T,MAN H C,CHENG F T. Cavitation erosion and pitting corrosion of laser surface melted stainless steels[J]. Surface and Coatings Technology,1998,99(3):295-304.
【5】KWOK C T,MAN H C,CHENG F T. Cavitation erosion and pitting corrosion behavior of laser surface-melted martensitic stainless steel UNSS42000[J]. Surface & Coatings Technology,2000,126(2/3):238-255.
【2】代真,沈士明,丁国铨. 金属在固液两相流体中的冲刷腐蚀及其防护[J]. 腐蚀与防护,2007,28(2):86-89.
【3】SCHMITT G,GUDDE T,STROBEL-EFFERTZ E. Fracture mechanical properties of CO2 corrosion product scales and their relation to localized corrosion[C]//Corrosion/1996. Houston,Texas:NACE,1996:96009.
【4】KWOK C T,MAN H C,CHENG F T. Cavitation erosion and pitting corrosion of laser surface melted stainless steels[J]. Surface and Coatings Technology,1998,99(3):295-304.
【5】KWOK C T,MAN H C,CHENG F T. Cavitation erosion and pitting corrosion behavior of laser surface-melted martensitic stainless steel UNSS42000[J]. Surface & Coatings Technology,2000,126(2/3):238-255.
相关信息
