Effect of Cerium Content on Microstructure and Properties of High Speed Steel Surfacing Layer
摘 要
采用钨极氩弧焊在低碳钢板上堆焊了含不同质量分数(0~0.4%)铈的高速钢堆焊层,研究了堆焊层的显微组织、物相组成、硬度和耐磨性能。结果表明:当铈质量分数在0~0.4%时,堆焊层的显微组织均由马氏体、残余奥氏体和VC、WC、Cr23C6等碳化物组成;随着铈含量的增加,堆焊层的表面硬度和耐磨性能均先增后降;当铈质量分数为0.1%时,堆焊层的表面硬度最高,为61.6 HRC,磨损量最小,为87.75×102 g·m-2,磨损形成的沟槽最浅,耐磨性能最好。
Abstract
High speed steel surfacing layers containing different mass fractions (0-0.4%) of cerium were deposited by tungsten inert gas arc welding on the low carbon steel plate, and then the microstructure, phase composition, hardness and wear resistance of surfacing layers were studied. The results show that with the cerium mass fractions of 0-0.4%, the microstructure of the surfacing layer was composed of martensite, retained austensite and carbides, such as VC, WC and Cr23C6. With the increase of cerium content, the surface hardness and wear resistance of the surfacing layer increased first and then decreased. When the cerium mass fraction was 0.1%, the surface hardness of the surfacing layer reached the highest value of 61.6 HRC, the wear loss had the lowest value of 87.75×102 g·m-2, and the groove formed by wear was the shallowest, indicating that the wear resistance was the best.
中图分类号 TG455 DOI 10.11973/jxgccl201808013
所属栏目 材料性能及应用
基金项目 国家自然科学基金资助项目(51601085)
收稿日期 2017/7/13
修改稿日期 2018/7/5
网络出版日期
作者单位点击查看
备注梁晨(1994-),男,河北唐山人,硕士研究生
引用该论文: LIANG Chen,SHI Haifang,YANG Zhihua,YANG Zhaofang. Effect of Cerium Content on Microstructure and Properties of High Speed Steel Surfacing Layer[J]. Materials for mechancial engineering, 2018, 42(8): 63~66
梁晨,时海芳,杨志华,杨兆方. 铈含量对高速钢堆焊层组织及性能的影响[J]. 机械工程材料, 2018, 42(8): 63~66
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】李萍. 碳、硼含量对含硼高速钢轧辊材料组织和性能的影响[D]. 西安:西安建筑科技大学, 2011.
【2】张群莉, 姚建华, 骆芳. 热作模具H13钢表面激光堆焊类高速钢的实验研究[J]. 材料热处理学报, 2005, 26(4):95-97.
【3】单际国, 董祖珏, 徐滨士. 我国堆焊技术的发展及其在基础工业中的应用现状[J]. 中国表面工程, 2002, 15(4):19-22.
【4】张绍顺. 高速钢复合轧辊的成分设计及生产工艺[J]. 有色金属加工, 2011, 40(5):43-45.
【5】顾锡峰, 莫胜功. 45钢/W6Mo5Cr4V2高速钢刀具的摩擦焊接研究[J]. 青海大学学报, 2009, 27(1):32-34.
【6】姚树玉, 李惠琪. 采煤机截齿堆焊高速钢涂层的研究[J]. 金属热处理, 2004, 29(8):51-54.
【7】刘先兰. 高速钢齿轮模数铣刀的合金堆焊修复工艺[J]. 工具技术, 2003, 37(5):37-39.
【8】石端虎, 印有胜. 稀土元素对堆焊层组织与性能的影响[J]. 沈阳工业大学学报, 2003, 25(5):384-386.
【9】尹柯, 李木白. 稀土及合金对粉块堆焊耐磨性的影响[J]. 焊接, 1998(1):9-12.
【2】张群莉, 姚建华, 骆芳. 热作模具H13钢表面激光堆焊类高速钢的实验研究[J]. 材料热处理学报, 2005, 26(4):95-97.
【3】单际国, 董祖珏, 徐滨士. 我国堆焊技术的发展及其在基础工业中的应用现状[J]. 中国表面工程, 2002, 15(4):19-22.
【4】张绍顺. 高速钢复合轧辊的成分设计及生产工艺[J]. 有色金属加工, 2011, 40(5):43-45.
【5】顾锡峰, 莫胜功. 45钢/W6Mo5Cr4V2高速钢刀具的摩擦焊接研究[J]. 青海大学学报, 2009, 27(1):32-34.
【6】姚树玉, 李惠琪. 采煤机截齿堆焊高速钢涂层的研究[J]. 金属热处理, 2004, 29(8):51-54.
【7】刘先兰. 高速钢齿轮模数铣刀的合金堆焊修复工艺[J]. 工具技术, 2003, 37(5):37-39.
【8】石端虎, 印有胜. 稀土元素对堆焊层组织与性能的影响[J]. 沈阳工业大学学报, 2003, 25(5):384-386.
【9】尹柯, 李木白. 稀土及合金对粉块堆焊耐磨性的影响[J]. 焊接, 1998(1):9-12.
相关信息