Effect of Process Conditions on Micro-arc Oxidation Coating of ZL205A Aluminum Alloy
摘 要
在硅酸钠电解液体系中,采用不同工艺在ZL205A铝合金表面制备微弧氧化层。通过测厚仪、扫描电镜、X射线衍射仪等研究了氧化电压和氧化时间对膜层性能的影响。结果表明:氧化膜主要由α-Al2O3、Mullite (Al6Si2O13)、Al相及非晶相组成;氧化层的放电通道孔径尺寸随氧化电压、时间的增加不断增大;随着氧化电压、时间的增加,氧化层厚度呈线性增长;氧化膜距离基体50 μm处的硬度(1 358 HV)高于距离基体200 μm处的(1 176 HV)。通过工艺条件调整可有效改善ZL205A铝合金微弧氧化层的膜层结构及性能。
Abstract
A micro-arc oxidation layer on ZL205A aluminum alloy was prepared in sodium silicate electrolyte system with different technologies. The effects of oxidation voltage and oxidation time on the properties of the film were investigated by means of thickness gauge, scanning electron microscope (SEM), X-ray diffractometer and so on. The results showed that the oxide film was mainly composed of α-Al2O3, Mullite (Al6Si2O13), Al phase and amorphous phase. The pore size of the discharge channel of the oxide layer increased with the increase of oxidation voltage and time; as the oxidation voltage and time increased, the thickness of the oxide layer increased linearly. The hardness of the oxide film at a distance of 50 μm from the substrate (1 358 HV) was higher than that at 200 μm from the substrate (1 176 HV). The film structure and properties of the micro-arc oxidation layer of ZL205A aluminum alloy can be effectively improved by adjusting the process conditions.
中图分类号 TG147 DOI 10.11973/fsyfh-201811014
所属栏目 应用技术
基金项目 国家重点基础研究发展计划(973计划)(2012CB625102);陕西省自然科学基础研究计划(2014JM2-5061)
收稿日期 2017/4/27
修改稿日期
网络出版日期
作者单位点击查看
引用该论文: LI Hongzhan,MA Youping,LI Zhengxian,DU Jihong,WANG Yifei,LI Shaolong. Effect of Process Conditions on Micro-arc Oxidation Coating of ZL205A Aluminum Alloy[J]. Corrosion & Protection, 2018, 39(11): 883
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】孙志华,刘明,王志申,等. 2A12铝合金微弧氧化陶瓷层的电化学腐蚀行为[J]. 腐蚀与防护,2014,35(4):352-356.
【2】贾泮江,陈邦峰. ZL205A高强铸造铝合金的性能及应用[J]. 轻合金加工技术,2009,37(11):10-12.
【3】崔世海,韩建民,李卫京,等. 高强铸造铝合金ZL205微弧氧化陶瓷膜的耐蚀性能研究[J]. 航空材料学报,2006,24(2):20-23.
【4】赵晖,朱其柱,金光,等. 电流密度对纯铝微弧氧化膜结构及硬度的影响[J]. 深圳大学学报(理工版),2014,31(1):83-87.
【5】赵英鹏,张晓燕,葛飞,等. 不同体系下铸造铝合金微弧氧化膜层的耐磨性能研究[J]. 轻金属,2012(2):60-62.
【6】吴振东,姜兆华,姚忠平,等. 纯铝及其合金微弧氧化陶瓷膜性能分析[J]. 稀有金属材料与工程,2006,35(增刊2):148-151.
【7】杨巍,蒋百灵,时惠英. LY12铝合金微弧氧化膜层的形成与生长机制[J]. 中国有色金属学报,2010,20(10):1949-1954.
【8】XIN S G,SONG L X,ZHAO R G. Properties of aluminum oxide coating on aluminum alloy produced by micro-arc oxidation[J]. Surface and Coatings Technology,2005,199(2):184-188.
【9】熊仁章,盛磊,郭洪光. 铝合金微弧氧化陶瓷层的耐磨性能[J]. 兵器材料科学与工程,2000,33(3):13-14.
【2】贾泮江,陈邦峰. ZL205A高强铸造铝合金的性能及应用[J]. 轻合金加工技术,2009,37(11):10-12.
【3】崔世海,韩建民,李卫京,等. 高强铸造铝合金ZL205微弧氧化陶瓷膜的耐蚀性能研究[J]. 航空材料学报,2006,24(2):20-23.
【4】赵晖,朱其柱,金光,等. 电流密度对纯铝微弧氧化膜结构及硬度的影响[J]. 深圳大学学报(理工版),2014,31(1):83-87.
【5】赵英鹏,张晓燕,葛飞,等. 不同体系下铸造铝合金微弧氧化膜层的耐磨性能研究[J]. 轻金属,2012(2):60-62.
【6】吴振东,姜兆华,姚忠平,等. 纯铝及其合金微弧氧化陶瓷膜性能分析[J]. 稀有金属材料与工程,2006,35(增刊2):148-151.
【7】杨巍,蒋百灵,时惠英. LY12铝合金微弧氧化膜层的形成与生长机制[J]. 中国有色金属学报,2010,20(10):1949-1954.
【8】XIN S G,SONG L X,ZHAO R G. Properties of aluminum oxide coating on aluminum alloy produced by micro-arc oxidation[J]. Surface and Coatings Technology,2005,199(2):184-188.
【9】熊仁章,盛磊,郭洪光. 铝合金微弧氧化陶瓷层的耐磨性能[J]. 兵器材料科学与工程,2000,33(3):13-14.
相关信息