Comparative Analysis on Standards for Sulfuric Acid-Copper Sulfate Intergranular Corrosion Test of Stainless Steels at Home and Abroad
摘 要
不锈钢硫酸-硫酸铜晶间腐蚀试验作为一种广泛应用的晶间腐蚀试验方法,各国对其制定了不同的标准。以GB/T 4334,ASTM A262,ISO 3651-2,RCC-M等标准为例,从试样制备、敏化处理、试验过程和结果评定4个方面对比分析了国内外各标准的差异。结果表明:国标和国外标准的规定不尽相同,实际操作过程中可适当相互借鉴;国标对试样制备的表述最为详细,试样表面粗糙度对试验结果的影响并不明显;国标对敏化处理制度的规定最为严格;弯曲参数的选择对试验结果存在一定的影响,过小的弯曲半径容易导致误判。
Abstract
Stainless steel sulfuric acid-copper sulfate intergranular corrosion test as a widely used intergranular corrosion test method, many countries have developed different standards for it. Taking GB/T 4334, ASTM A262, ISO 3651-2, RCC-M and other standards as examples, the similarities and differences among above domestic and foreign standards were compared and analyzed from four aspects:sample preparation, sensitization treatment, test process and result evaluation. The results show that the requirements of national standard and foreign standards are not the same, and they can be used for reference in the actual operation process. The national standard has the most detailed expression of sample preparation, and the effect of surface roughness of the sample on the test results is not significant. The national standard has the strictest regulations on the sensitization treatment system. The selection of the bending parameters has a certain influence on the test results, and too small bending radius is likely to lead to misjudgement.
中图分类号 TB302 DOI 10.11973/lhjy-wl201902007
所属栏目 标准化
基金项目
收稿日期 2018/10/17
修改稿日期
网络出版日期
作者单位点击查看
备注张艳(1987-),女,助理工程师,硕士,主要从事压力容器的设计、制造与检验等工作,1309916194@qq.com
引用该论文: ZHANG Yan,WAN Zhang,WANG Xiaofeng,WU Lei,XU Pengcheng. Comparative Analysis on Standards for Sulfuric Acid-Copper Sulfate Intergranular Corrosion Test of Stainless Steels at Home and Abroad[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2019, 55(2): 102~107
张艳,万章,王晓峰,吴磊,徐鹏程. 不锈钢硫酸-硫酸铜晶间腐蚀试验国内外标准对比解析[J]. 理化检验-物理分册, 2019, 55(2): 102~107
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】査小琴, 李永军,李雪峰,等. 不锈钢硫酸-硫酸铜晶间腐蚀结果评定方法探讨[J]. 材料开发与应用,2016(6):35-40.
【2】张凯. 06Cr19Ni10奥氏体不锈钢晶间腐蚀的解析[J]. 内江师范学院学报,2015(4):18-20,38.
【3】吴庭翱,查小琴. 不锈钢硫酸-硫酸铜晶间腐蚀试验结果评定方法[J]. 材料开发与应用,2015,30(1):43-49.
【4】李茂林,成欢,武贵斌,等. 核级奥氏体不锈钢无缝钢管晶间腐蚀研究[J]. 热加工工艺,2014,43(8):75-77.
【5】李长香,杨敏. 对RCC-M规范中奥氏体不锈钢晶间腐蚀试样状态和数量要求的分析[J]. 核标准计量与质量,2012(4):7-10.
【6】邱智伟,王国珍,轩福贞. 不锈钢晶间腐蚀弯曲评价方法的影响因素[J]. 理化检验(物理分册),2012,48(8):495-499.
【7】戴永祥,连芳,李吉,等. 304不锈钢的晶间腐蚀行为研究[J]. 轻型汽车技术,2011(增刊2):34-37.
【8】张胜寒,李娜,杨妮. 316不锈钢的晶间腐蚀行为的研究[J]. 汽轮机技术,2009,51(1):78-80.
【9】秦丽雁,张寿禄,宋诗哲. 典型不锈钢晶间腐蚀敏化温度的研究[J]. 中国腐蚀与防护学报,2006,26(1):1-5.
【10】李茂林,浦承皓,王卫东,等. 奥氏体不锈钢无缝钢管晶间腐蚀试验要求探讨[J]. 中国材料进展,2017,36(11):868-872.
【11】黄嘉琥. 不锈钢晶间腐蚀GB/T 21433-2008《不锈钢压力容器晶间腐蚀敏感性检验》标准释义[M]. 北京:新华出版社,2008.
【12】金维松,郎宇平,荣凡,等. EPR法评价奥氏体不锈钢晶间腐蚀敏感性的研究[J]. 中国腐蚀与防护学报,2007,27(1):54-59.
【2】张凯. 06Cr19Ni10奥氏体不锈钢晶间腐蚀的解析[J]. 内江师范学院学报,2015(4):18-20,38.
【3】吴庭翱,查小琴. 不锈钢硫酸-硫酸铜晶间腐蚀试验结果评定方法[J]. 材料开发与应用,2015,30(1):43-49.
【4】李茂林,成欢,武贵斌,等. 核级奥氏体不锈钢无缝钢管晶间腐蚀研究[J]. 热加工工艺,2014,43(8):75-77.
【5】李长香,杨敏. 对RCC-M规范中奥氏体不锈钢晶间腐蚀试样状态和数量要求的分析[J]. 核标准计量与质量,2012(4):7-10.
【6】邱智伟,王国珍,轩福贞. 不锈钢晶间腐蚀弯曲评价方法的影响因素[J]. 理化检验(物理分册),2012,48(8):495-499.
【7】戴永祥,连芳,李吉,等. 304不锈钢的晶间腐蚀行为研究[J]. 轻型汽车技术,2011(增刊2):34-37.
【8】张胜寒,李娜,杨妮. 316不锈钢的晶间腐蚀行为的研究[J]. 汽轮机技术,2009,51(1):78-80.
【9】秦丽雁,张寿禄,宋诗哲. 典型不锈钢晶间腐蚀敏化温度的研究[J]. 中国腐蚀与防护学报,2006,26(1):1-5.
【10】李茂林,浦承皓,王卫东,等. 奥氏体不锈钢无缝钢管晶间腐蚀试验要求探讨[J]. 中国材料进展,2017,36(11):868-872.
【11】黄嘉琥. 不锈钢晶间腐蚀GB/T 21433-2008《不锈钢压力容器晶间腐蚀敏感性检验》标准释义[M]. 北京:新华出版社,2008.
【12】金维松,郎宇平,荣凡,等. EPR法评价奥氏体不锈钢晶间腐蚀敏感性的研究[J]. 中国腐蚀与防护学报,2007,27(1):54-59.
相关信息