超音速火焰喷涂WC-17Co合金涂层修复飞机燃油接受探管导轨磨损部位
Wear Part Repairing of Aircraft Refueling Probe Guide Rail by High-Velocity Oxygen Fuel Sprayed WC-17Co Alloy Coating
摘 要
某型飞机燃油接受探管外筒导轨镀铬层发生磨损剥落，采用超音速火焰（HVOF）喷涂WC-17Co合金涂层对其进行修复，研究了HVOF涂层的微观形貌、力学性能和耐磨性能，并对导轨修复的燃油接受探管进行了20次全行程收放转换模拟试验、30次地面运行试验和50次空中飞行运行试验。结果表明：HVOF涂层的硬度高达1 041 HV，与导轨基体的结合强度大于85.4 MPa，涂层韧性良好，耐磨性能优于电镀铬层的，且与化学镀镍磨轮配对时的对磨表面磨损程度很小；修复导轨组装的探管在收放转换模拟试验和运行试验后，其HVOF涂层均未见磨损现象，修复导轨的使用状态良好。
燃油接受探管
损伤修复
WC-17Co合金涂层
high-velocity oxygen fuel spraying
refueling probe
damage repairing
WC-17Co alloy coating
Abstract
A certain type aircraft refueling probe was subjected to wear and spalling in the chrome-plated layer of the extenal guide rail. WC-17Co alloy coating by high-velocity oxygen fuel (HVOF) spraying was used to repair the guide rail. The micromorphology, mechanical properties and wear resistance of the HVOF coating was studied. The refueling probe with the repaired guide rail was subjected to 20 full-stroke extending and retracting simulation tests, 30 ground running tests and 50 air flight running tests. The results show that the hardness of the HVOF coating was up to 1 041 HV and the bonding strength with the guide rail substrate was greater than 85.4 MPa. The toughness of the coating was good, the wear resistance was higher than that of electroplated chrome layer, and the wear degree of the grinding surface was small when paired with the electroless nickel plated wheel. After extending and retracting simulation tests and running tests of the probe assembled with the repaired guide rail, the HVOF coating on the guide rail showed no wear features and the repaired guide rail was in good condition.
中图分类号 TG147.442 DOI 10.11973/jxgccl201904010
所属栏目 新材料 新工艺
基金项目
收稿日期 2018/9/7
修改稿日期 2019/3/20
网络出版日期
作者单位点击查看
备注唐斌(1963-),男,江苏海安人,高级工程师,学士
引用该论文: TANG Bin,SUN Xiao,DU Qiang,ZHU Jie. Wear Part Repairing of Aircraft Refueling Probe Guide Rail by High-Velocity Oxygen Fuel Sprayed WC-17Co Alloy Coating[J]. Materials for mechancial engineering, 2019, 43(4): 44～47
唐斌,孙霄,杜强,朱杰. 超音速火焰喷涂WC-17Co合金涂层修复飞机燃油接受探管导轨磨损部位[J]. 机械工程材料, 2019, 43(4): 44～47
共有人对该论文发表了看法，其中：
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】苏新勇, 刘基凯, 杨秀红, 等. 船用辅汽轮机转子汽封轴颈喷涂WC-12Co涂层的摩擦学性能[J]. 中国表面工程, 2011, 24(5):89-93.
【2】WANG Y Y, LI C J, MA J, et al. Effect of flame conditions on abrasive wear performance of HVOF sprayed nanostructured WC-12Co coatings[J]. Transactions of Nonferrous Metals Society of China, 2004, 14(S2):72-76.
【3】王群, 丁彰雄, 陈振华, 等. 超音速火焰喷涂微米和纳米结构WC-12Co涂层及其性能[J].机械工程材料,2007,31(4):17-20.
【4】周夏凉, 陈小明, 吴燕明, 等. 超音速火焰喷涂WC-10Co4Cr涂层的力学性能及断裂机理[J].机械工程材料,2015,39(10):52-55.
【5】郑毅, 郑卫刚, 吕松. 超音速火焰喷涂碳化钨涂层与电镀硬铬镀层的对比研究[J]. 机械制造, 2013, 51(8):86-88.
【2】WANG Y Y, LI C J, MA J, et al. Effect of flame conditions on abrasive wear performance of HVOF sprayed nanostructured WC-12Co coatings[J]. Transactions of Nonferrous Metals Society of China, 2004, 14(S2):72-76.
【3】王群, 丁彰雄, 陈振华, 等. 超音速火焰喷涂微米和纳米结构WC-12Co涂层及其性能[J].机械工程材料,2007,31(4):17-20.
【4】周夏凉, 陈小明, 吴燕明, 等. 超音速火焰喷涂WC-10Co4Cr涂层的力学性能及断裂机理[J].机械工程材料,2015,39(10):52-55.
【5】郑毅, 郑卫刚, 吕松. 超音速火焰喷涂碳化钨涂层与电镀硬铬镀层的对比研究[J]. 机械制造, 2013, 51(8):86-88.
相关信息
