Application of Parallax Method and CIVA Simulation in Defect Depth Location of Digital Radiography Testing
摘 要
介绍了精确式视差法测量缺陷深度的原理,通过带缺陷试样的数字射线透照试验,结合CIVA软件仿真模拟,探究了该方法的可行性,分析了影响测量精度的因素。采用数字成像技术替代常规胶片成像技术,弥补了其检测效率低、测量困难、测量误差大等不足。同时引入了验证标记对测量结果进行准确验证,避免了因操作原因造成的定位误差。
Abstract
In this paper, the principle of measuring the depth of defects by parallax method is introduced. Through the digital radiography testing with defective workpiece and CIVA simulation, the feasibility of the method is explored and the factors influencing the measurement accuracy are analyzed. Digital radiography technology makes up for the disadvantages of conventional film imaging technology such as low detection efficiency, difficulty in measurement, and large measurement error. At the same time, the verification mark is introduced to accurately verify the measurement result, and the positioning error caused by the operation is avoided.
中图分类号 TG115.28 DOI 10.11973/wsjc201905004
所属栏目 试验研究
基金项目
收稿日期 2018/8/17
修改稿日期
网络出版日期
作者单位点击查看
备注华雄飞(1985-),男,硕士,工程师,主要从事核电站役前、在役无损检测工作
引用该论文: HUA Xiongfei,FAN Mingyan,LIU Shun,LIN Shichang,FAN Yi. Application of Parallax Method and CIVA Simulation in Defect Depth Location of Digital Radiography Testing[J]. Nondestructive Testing, 2019, 41(5): 14~17
华雄飞,樊明岩,刘顺,林世昌,范义. 视差法及CIVA仿真在数字射线检测缺陷深度定位中的应用[J]. 无损检测, 2019, 41(5): 14~17
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】郑世才.射线检测[M].北京:机械工业出版社,2004.
【2】蔡闰生,任华友.X射线照相缺陷定位方法分析与验证[J].宇航材料工艺, 2013,43(3):129-133.
【3】李衍,李华.焊缝射线照相缺陷测深技术[J].中国锅炉压力容器安全,2001,17(5):40-43,46.
【4】杨飞. X射线数字成像中的缺陷定位检测技术研究[D].太原:中北大学,2003:6-7.
【5】刘海强,熊瑛,郭佳,等.射线平移二次缺陷定位方法的探讨[J].无损探伤, 2016,40(5):43-45.
【2】蔡闰生,任华友.X射线照相缺陷定位方法分析与验证[J].宇航材料工艺, 2013,43(3):129-133.
【3】李衍,李华.焊缝射线照相缺陷测深技术[J].中国锅炉压力容器安全,2001,17(5):40-43,46.
【4】杨飞. X射线数字成像中的缺陷定位检测技术研究[D].太原:中北大学,2003:6-7.
【5】刘海强,熊瑛,郭佳,等.射线平移二次缺陷定位方法的探讨[J].无损探伤, 2016,40(5):43-45.
相关信息