Technical Key Points of Using Digital Metallographic Microscope to Take High Quality Metallographic Photographs
摘 要
介绍了数码金相显微镜的优点,并列举了典型的金相照片。从摄像头硬件、原材料质量、金相试样制备方法和拍摄技巧等几方面,详细阐述了拍摄出高质量金相照片的技术要点。结果表明:拍摄出高质量的金相照片,除了摄像头硬件的影响因素之外,还要求金相试样观察面要磨制平整,必要时需对试样进行镶嵌;金相试样抛光后表面应无划痕,且选择合适的浸蚀剂,浸蚀程度要恰到好处;在拍摄金相照片时注意亮度要适中,放大倍数要适当;校正好白平衡;拍摄偏光照片时要调节检偏滑尺角度,使图像颜色对比最为明显。
Abstract
The advantages of digital metallographic microscope were introduced, and typical metallographic photographs were listed. From the aspects of camera hardware, raw material quality, metallographic sample preparation method and photo shooting skills, the key points of taking high quality metallographic photographs were elaborated in detail. The results show that in order to high quality metallographic photographs, besides the influence factors of the camera hardware the observation surface of the metallographic samples should be grinded flat, and the samples should be mounted when necessary. The polished surface of metallographic samples should be free of scratches, and the appropriate etchant should be selected to achieve the right degree of etching. When taking metallographic photographs, the brightness and the magnification should be appropriate. Corrected the white balance. When taking polarized photographs, the angle of the deviation detection slider should be adjusted to make the color contrast of the images most obvious.
中图分类号 TG113.1 DOI 10.11973/lhjy-wl201905009
所属栏目 试验技术与方法
基金项目 河北省高等教育教学改革研究与实践项目(2018GJJG082)
收稿日期 2018/12/29
修改稿日期
网络出版日期
作者单位点击查看
备注李慧(1962-),女,高级实验师,主要从事金属材料显微组织分析及性能研究工作,lihui@ysu.edu.cn
引用该论文: LI Hui,LIU Jianhua,YANG Meng,QU Minggui. Technical Key Points of Using Digital Metallographic Microscope to Take High Quality Metallographic Photographs[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2019, 55(5): 321~325
李慧,刘建华,杨猛,曲明贵. 使用数码金相显微镜拍摄高质量金相照片的技术要点[J]. 理化检验-物理分册, 2019, 55(5): 321~325
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】毕革平,吴京利,李江豫,等. 数码照相技术在金相显微镜上的应用[J]. 钢铁研究学报,1999,11(6):57-59.
【2】段莉萍,苑东,盛磊,等. 计算机在金相分析技术中的应用[J]. 理化检验(物理分册),1996,35(6):272-274.
【3】张照军,张思遥. 金相显微镜数字图像采集系统的改造[J]. 金属热处理,2012,37(12):134-135.
【4】张宏. CCD在金相显微镜中的应用研究[J]. 实验室研究与探索,2000,19(1):41-44.
【5】童建华,李芳. 金相样品制备中的假象对组织鉴别的影响[J]. 金属热处理,2009,34(5):79-82.
【6】王朋,龙思远,杨承志,等. 铸态Mg-Nd-Zn-Zr镁合金用腐蚀剂比较[J]. 金属热处理,2016,41(6):168-171.
【7】刘宗昌,李一鸣. 钢的显微组织识别[J]. 金属热处理,2016,41(8):199-204.
【8】田晓璇,肖国华,曹剑峰,等. P91钢现场快速金相检验方法[J]. 理化检验(物理分册),2015,51(12):867-869.
【9】万长杰,白瑞娟,申丽娟,等. 45钢原始奥氏体晶界的显示方法[J]. 理化检验(物理分册),2016,52(3):174-176.
【2】段莉萍,苑东,盛磊,等. 计算机在金相分析技术中的应用[J]. 理化检验(物理分册),1996,35(6):272-274.
【3】张照军,张思遥. 金相显微镜数字图像采集系统的改造[J]. 金属热处理,2012,37(12):134-135.
【4】张宏. CCD在金相显微镜中的应用研究[J]. 实验室研究与探索,2000,19(1):41-44.
【5】童建华,李芳. 金相样品制备中的假象对组织鉴别的影响[J]. 金属热处理,2009,34(5):79-82.
【6】王朋,龙思远,杨承志,等. 铸态Mg-Nd-Zn-Zr镁合金用腐蚀剂比较[J]. 金属热处理,2016,41(6):168-171.
【7】刘宗昌,李一鸣. 钢的显微组织识别[J]. 金属热处理,2016,41(8):199-204.
【8】田晓璇,肖国华,曹剑峰,等. P91钢现场快速金相检验方法[J]. 理化检验(物理分册),2015,51(12):867-869.
【9】万长杰,白瑞娟,申丽娟,等. 45钢原始奥氏体晶界的显示方法[J]. 理化检验(物理分册),2016,52(3):174-176.
相关信息