Failure Analysis on Fracture of an Air Conditioning Compressor Spring
摘 要
某空调压缩机弹簧在系统耐久试验期间发生断裂,采用断口分析、金相检验、化学成分分析、硬度测试等方法对弹簧的断裂原因进行了分析,并对弹簧的疲劳强度进行了校核,对弹簧进行了喷丸工艺改善研究。结果表明:该弹簧实际工作时最大切应力高于材料的许用切应力,在循环载荷作用下安全系数不足,最终发生了疲劳断裂;喷丸工艺可以提高弹簧的可靠性,采用φ0.2 mm钢球喷丸处理后的弹簧表面形貌最优且疲劳寿命最高。
Abstract
The air condition compressor springs broke during the durability test of the system. Fracture analysis, metallographic examination, chemical composition analysis and hardness test were used to analyze the fracture causes of the springs. The fatigue strength of the springs was checked and the improvement of the shot peening process was also studied. The results show that the maximum shear stress of the springs in practice was higher than the allowable shear stress of the material. The safety factor of the springs was insufficient under cyclic loading, and fatigue fracture finally occurred. The reliability of springs could be improved by shot peening process. The springs treated by shot peening with φ0.2 mm steel balls had the best surface morphology and the highest fatigue life.
中图分类号 TG142.1 DOI 10.11973/lhjy-wl201905012
所属栏目 质量控制与失效分析
基金项目
收稿日期 2019/1/3
修改稿日期
网络出版日期
作者单位点击查看
备注李子阳(1989-),男,工程师,主要从事空调压缩机零部件材料研究,liziyang365@163.com
引用该论文: LI Ziyang,ZHU Weiheng. Failure Analysis on Fracture of an Air Conditioning Compressor Spring[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2019, 55(5): 333~337
李子阳,朱伟恒. 某空调压缩机弹簧断裂失效分析[J]. 理化检验-物理分册, 2019, 55(5): 333~337
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】于汇泳, 周慧琳,胡俊华. 弹簧振动失效断口分析[J]. 机械设计与制造, 2013(3):260-264.
【2】王仁智. 残余应力与弹簧的疲劳性能[J]. 理化检验(物理分册),2005,41(11):541-548.
【3】徐宏伟,孙玉秋,张祖明. 考虑多种失效模式圆柱螺旋拉压弹簧的可靠性设计[J]. 机械设计与制造,2002(3):6-8.
【4】傅华栋. 圆柱螺旋弹簧疲劳试验方法研究[D]. 北京:机械科学研究总院,2007.
【5】唐海中,黄春红,吴彩芬. 圆柱螺旋压缩弹簧断裂失效分析[J]. 理化检验(物理分册),2016,52(12):900-902.
【6】王仁智,杨伟明,邬秋林. 外施应力与表面残余应力作用下圆柱螺旋压缩弹簧任意截面的受力分析[J]. 理化检验(物理分册),2007,43(1):1-5.
【7】徐效谦. 钢丝索氏体化工艺探讨[C]//第十届中国科协年会论文集. 郑州:第十届中国科协年会,2008:1035-1044.
【8】彭小钢,曹标,谭莹. 弹簧钢丝拉拔断裂原因分析[J]. 理化检验(物理分册),2017,53(8):599-606.
【9】邢献强,菅军伟. 55CrSi油淬火回火弹簧钢丝卷簧断裂分析[J]. 金属制品,2014,40(6):31-33.
【10】成大先. 机械设计手册(第五版)[M]. 北京:化学工业出版社,2008.
【11】宾技慧. 喷丸强化技术对弹簧疲劳寿命的影响[J]. 机械工业标准化与质量,1998(11):22-25.
【2】王仁智. 残余应力与弹簧的疲劳性能[J]. 理化检验(物理分册),2005,41(11):541-548.
【3】徐宏伟,孙玉秋,张祖明. 考虑多种失效模式圆柱螺旋拉压弹簧的可靠性设计[J]. 机械设计与制造,2002(3):6-8.
【4】傅华栋. 圆柱螺旋弹簧疲劳试验方法研究[D]. 北京:机械科学研究总院,2007.
【5】唐海中,黄春红,吴彩芬. 圆柱螺旋压缩弹簧断裂失效分析[J]. 理化检验(物理分册),2016,52(12):900-902.
【6】王仁智,杨伟明,邬秋林. 外施应力与表面残余应力作用下圆柱螺旋压缩弹簧任意截面的受力分析[J]. 理化检验(物理分册),2007,43(1):1-5.
【7】徐效谦. 钢丝索氏体化工艺探讨[C]//第十届中国科协年会论文集. 郑州:第十届中国科协年会,2008:1035-1044.
【8】彭小钢,曹标,谭莹. 弹簧钢丝拉拔断裂原因分析[J]. 理化检验(物理分册),2017,53(8):599-606.
【9】邢献强,菅军伟. 55CrSi油淬火回火弹簧钢丝卷簧断裂分析[J]. 金属制品,2014,40(6):31-33.
【10】成大先. 机械设计手册(第五版)[M]. 北京:化学工业出版社,2008.
【11】宾技慧. 喷丸强化技术对弹簧疲劳寿命的影响[J]. 机械工业标准化与质量,1998(11):22-25.
相关信息