Tensile Behavior of LB27 and LB20 Aluminum-Clad Steel Wires
摘 要
采用铝连续挤压包覆法用SWRS72A钢和SWRS82B钢分别制备了LB27和LB20铝包钢芯线,制备冷拔前后的试样并对其进行了室温拉伸试验,研究了试样的拉伸性能和拉伸断口形貌。结果表明:未包覆铝SWRS72A钢的屈服强度和抗拉强度均高于包覆铝后冷拔前的;和未包覆铝SWRS72A钢相比,LB27铝包钢芯线的屈服强度更高,但抗拉强度稍有下降,延伸率显著下降;随着外径的增加,LB20铝包钢芯线屈服强度逐渐减小,其屈服强度均大于LB27铝包钢芯线的;LB20铝包钢芯线的断口形貌和LB27铝包钢芯线相似,但其钢丝边部存在剪切唇。
Abstract
LB27 and LB20 aluminum-clad steel wires were prepared by continuous extrusion cladding of aluminum with SWRS72A steel and SWRS82B steel, respectively. Samples before and after cold drawing were prepared and tensile experiments were conducted on them at room temperature. The tensile properties and fracture morphology of the samples were studied. The results show that the yield strength and tensile strength of the SWRS72A steel without aluminum cladding were higher than those with aluminum cladding before cold drawing. Compared with SWRS72A steel without aluminum cladding, the yield strength of the LB27 aluminum-clad steel wire was higher, but the tensile strength decreased slightly. The elongation of the LB27 aluminum-clad steel wire decreased significantly. With the increase of outer diameter, the yield strength of the LB20 aluminum-clad steel wire decreased gradually, but was greater than that of the LB27 aluminum-clad steel wire. The fracture morphology of the LB20 aluminum-clad steel wire was similar to that of the LB27 aluminum-clad steel wire, but shear lip existed at the edge of the steel of the LB20 aluminum-clad steel wire.
中图分类号 TG142.21 DOI 10.11973/jxgccl201909005
所属栏目 试验研究
基金项目
收稿日期 2018/5/30
修改稿日期 2019/6/17
网络出版日期
作者单位点击查看
备注田嘉治(1993-),男,江苏邳州人,学士
引用该论文: TIAN Jiazhi,ZHENG Chengming,JIANG Zechao,TIAN Qingchao. Tensile Behavior of LB27 and LB20 Aluminum-Clad Steel Wires[J]. Materials for mechancial engineering, 2019, 43(9): 23~27
田嘉治,郑成明,江泽超,田青超. LB27和LB20铝包钢芯线的拉伸行为[J]. 机械工程材料, 2019, 43(9): 23~27
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】张强, 陈保安, 祝志祥, 等. 架空导线用芯线材料综述[J]. 热加工工艺, 2016, 45(6):20-22.
【2】段国权, 王金麟, 邓良, 等. 铝包钢线的生产技术及其在架空输电线路中的应用[J]. 电线电缆, 2005,34(1):3-7.
【3】段建华, 刘晓文. 铝包钢绞线的生产技术与应用[J]. 金属制品, 2004, 30(1):1-4.
【4】段建华. 压力润滑技术在拉丝中的应用[J]. 金属制品, 2008, 34(1):11-12.
【5】郭其生, 汪小五, 徐磊岗, 等. 新技术在铝包钢线生产中的开发应用[J]. 电线电缆, 2011,40(3):18-21.
【6】宋志良, 周建华, 孙光进, 等. 特高强度铝包钢线生产工艺研究[J]. 电线电缆, 2012,41(5):20-21.
【7】刘洪伟, 郭成, 臧顺来. 不锈钢-铝合金复层材料拉伸力学性能分析[J]. 中国机械工程, 2007, 18(7):862-865.
【8】BORCHERS C, KIRCHHEIM R. Cold-drawn pearlitic steel wires[J]. Progress in Materials Science, 2016, 82:405-444.
【9】孙杰, 刘礼华, 程晓农, 等. 82B盘条断裂形式及原因分析[J]. 金属制品, 2012, 38(1):61-64.
【10】史志远, 陈彦博, 曹汉民, 等. 连续铸挤铝包钢线复合机理[J]. 中国有色金属学报, 1998, 8(增刊1):154-158.
【11】LANGUILLAUME J, KAPELSKI G, BAUDELET B. Cementite dissolution in heavily cold drawn pearlitic steel wires[J]. Acta Materialia, 1997, 45(3):1201-1212.
【12】TANIYAMA A, TAKAYAMA T, ARAI M, et al. Structure analysis of ferrite in deformed pearlitic steel by means of X-ray diffraction method with synchrotron radiation[J]. Scripta Materialia, 2004, 51(1): 53-58.
【2】段国权, 王金麟, 邓良, 等. 铝包钢线的生产技术及其在架空输电线路中的应用[J]. 电线电缆, 2005,34(1):3-7.
【3】段建华, 刘晓文. 铝包钢绞线的生产技术与应用[J]. 金属制品, 2004, 30(1):1-4.
【4】段建华. 压力润滑技术在拉丝中的应用[J]. 金属制品, 2008, 34(1):11-12.
【5】郭其生, 汪小五, 徐磊岗, 等. 新技术在铝包钢线生产中的开发应用[J]. 电线电缆, 2011,40(3):18-21.
【6】宋志良, 周建华, 孙光进, 等. 特高强度铝包钢线生产工艺研究[J]. 电线电缆, 2012,41(5):20-21.
【7】刘洪伟, 郭成, 臧顺来. 不锈钢-铝合金复层材料拉伸力学性能分析[J]. 中国机械工程, 2007, 18(7):862-865.
【8】BORCHERS C, KIRCHHEIM R. Cold-drawn pearlitic steel wires[J]. Progress in Materials Science, 2016, 82:405-444.
【9】孙杰, 刘礼华, 程晓农, 等. 82B盘条断裂形式及原因分析[J]. 金属制品, 2012, 38(1):61-64.
【10】史志远, 陈彦博, 曹汉民, 等. 连续铸挤铝包钢线复合机理[J]. 中国有色金属学报, 1998, 8(增刊1):154-158.
【11】LANGUILLAUME J, KAPELSKI G, BAUDELET B. Cementite dissolution in heavily cold drawn pearlitic steel wires[J]. Acta Materialia, 1997, 45(3):1201-1212.
【12】TANIYAMA A, TAKAYAMA T, ARAI M, et al. Structure analysis of ferrite in deformed pearlitic steel by means of X-ray diffraction method with synchrotron radiation[J]. Scripta Materialia, 2004, 51(1): 53-58.
相关信息