搜索热:失效分析 陶瓷
扫一扫 加微信
首页 > 期刊论文 > 论文摘要
蒸汽发生器传热管涡流检测的相位特性
          
Study on phase characteristics of eddy current detection for heat transfer tube of steam generator

摘    要
针对核电的安全问题,采用Bobbin线圈传感器对蒸气发生器传热管的各种类型缺陷进行涡流检测,分析了缺陷与涡流阻抗信号、相位信号之间的关系,并对检测频率进行了优化,通过相位信号实现了对不同缺陷的检测。
标    签 核电   蒸气发生器传热管   涡流检测   Bobbin线圈   nuclear power   steam generator heat transfer tube   eddy current testing   Bobbin coil  
 
Abstract
On the safety of nuclear power,the Bobbin coil is used to perform eddy current testing on various types of defects of the steam generator heat transfer tube. The relationship between defects and eddy current impedance signal and phase signal is analyzed. The detection frequency is optimized. Different defects are detected by phase signals.

中图分类号 TG115.28   DOI 10.11973/wsjc201911005

 
  中国光学期刊网论文下载说明


所属栏目 2019远东无损检测新技术论坛论文精选

基金项目

收稿日期 2019/6/27

修改稿日期

网络出版日期

作者单位点击查看


备注李明达(1989-),男,硕士研究生,主要从事电磁无损检测工作

引用该论文: LI Mingda,ZHOU Deqiang,BEI Yayao. Study on phase characteristics of eddy current detection for heat transfer tube of steam generator[J]. Nondestructive Testing, 2019, 41(11): 17~21
李明达,周德强,贝雅耀. 蒸汽发生器传热管涡流检测的相位特性[J]. 无损检测, 2019, 41(11): 17~21


论文评价
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
分享论文
分享到新浪微博 分享到腾讯微博 分享到人人网 分享到 Google Reader 分享到百度搜藏分享到Twitter

参考文献
【1】YOON B, KIM Y, YANG S. An experimental result on flaw sizing of steam generator tube at nuclear power plants using ultrasonic testing [J].Journal of Nuclear Science and Technology,2012,49(7):760-767.
 
【2】马强, 孔玉莹, 顾波, 等. 蒸汽发生器传热管防振条位置涡流定位检验精度研究[J]. 核动力工程, 2017, 38(4): 108-111.
 
【3】SHIM H S, CHOI M S, LEE D H, et al. A prediction method for the general corrosion behavior of Alloy 690 steam generator tube using eddy current testing[J]. Nuclear Engineering and Design, 2016, 297: 26-31.
 
【4】TODOROV E. Measurement of electromagnetic properties of heat exchanger tubes[J]. NDT & E International, 2012, 48: 63-69.
 
【5】于翔. 基于涡流传感器的便携式无损检测器装置设计及算法研究[D]. 沈阳: 东北大学, 2013.
 
相关信息
   标题 相关频次
 1 000 MW核电机组主蒸汽隔离阀基板块螺栓裂纹分析
 2
 12 mm不锈钢异型管件涡流检测
 2
 304奥氏体不锈钢涡流检测频率的优化
 2
 304不锈钢在核电站二回路水环境中的应力腐蚀开裂行为
 2
 5A06薄壁球壳件涡流检测技术
 2
 8 mm铜杆穿过式涡流探头校准方法
 2
 AVR单片机在预多频激励信号源中的应用
 2
 DR与传统胶片技术在核电检测中的能效对比
 2
 X型涡流探头对裂纹类缺陷测量的响应规律
 2
 奥氏体不锈钢换热器管的涡流检测
 2
 便携式多功能涡流仪的研制
 2
 便携式内窥镜系统CMOS图像传感器驱动设计与实现
 2
 表面粗糙度对涡流检测的影响
 2
 薄壁管涡流检测的不确定度评定
 2
 不锈钢储液罐的涡流检测
 2
 不锈钢管件裂纹深度的涡流阻抗分析
 2
 不锈钢焊缝的涡流正交探头检测试验
 2
 传感器触头罩的涡流检测
 2
 传热管内相位大于40°的缺陷信号分析
 2
 磁饱和后的涡流检测信号的非涡流效应
 2
 道岔尖轨表面缺陷检测卡片式涡流传感器的设计与应用
 2
 电磁超声和涡流组合检测方法
 2
 动车变流器安装座焊缝涡流检测的灵敏度验证
 2
 锻钢冷轧辊涡流检测技术
 2
 防振条位置的涡流检测
 2
 飞机辅助动力装置尾管组件的渗透和涡流检测
 2
 飞机维修中涡流检测对比试块的设计和应用
 2
 钢管涡流检测时信号扇形显示与幅值显示对缺陷判别的影响
 2
 钢管涡流探伤中缺陷信号的相位分辨
 2
 钢球表面缺陷识别方法
 2