Erosion Corrosion Simulation of Liquid-solid Two-phase Flow in 90 Degree Vertical Bend Pipes
摘 要
以液固两相流条件下的90°竖直弯管为研究对象,建立冲蚀模型,利用ANSYS-Fluent软件对A、B、C、D四种流向的弯管进行冲刷腐蚀数值模拟。同时建立室内冲蚀试验平台,分析了颗粒入口流速、粒径和质量流量三个参数对四种流向条件下弯管的冲蚀破坏规律并与模拟结果进行对比。结果表明:试验结果与模拟结果基本吻合,入口流速和粒径对弯管的冲蚀影响最大;且随着颗粒入口流速的增大,流场中开始出现二次流。当颗粒入口流速较小时,A型流向条件下弯管的冲蚀破坏最严重;而当颗粒入口流速较大时,由于二次流加剧冲刷,B型流向条件下弯管的冲蚀破坏最严重,A型、C型流向条件下的次之,D型流向条件下的弯管冲蚀破坏最小。
Abstract
A 90° vertical bend under the condition of liquid-solid two-phase flow was taken as the research object, and an erosion model was established. ANSYS-Fluent software was used to simulate the erosion corrosion of four flow tubes A, B, C and D. At the same time, an indoor erosion test platform was established, and the erosion failure law of the three parameters of particle inlet flow velocity, particle size and mass flow rate under four flow conditions was analyzed and compared with the simulation results. The results show that the experimental results were basically consistent with the simulation results, and the inlet flow velocity and particle size had the greatest influence on the erosion of the bend, and as the particle inlet flow rate increased, secondary flow began to appear in the flow field. When the particle inlet flow rate was small, the erosion of the elbow in the type A flow direction was the most severe. When the particle inlet flow velocity was large, the erosion bend under B-type flow direction condition was the most serious due to the secondary flow intensified, and the A-type and C-type flow conditions are the second, and the erosion of the bend under D-flow conditions was minimal.
中图分类号 TG17 DOI 10.11973/fsyfh-202001010
所属栏目 应用技术
基金项目
收稿日期 2018/5/12
修改稿日期
网络出版日期
作者单位点击查看
联系人作者赵会军(zhj@cczu.edu.cn)
引用该论文: SHEN Yaxin,ZHAO Huijun,PENG Haoping,CI Zhi,CHENG Yawen,ZHANG Jiayuan. Erosion Corrosion Simulation of Liquid-solid Two-phase Flow in 90 Degree Vertical Bend Pipes[J]. Corrosion & Protection, 2020, 41(1): 50
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】代真, 段志祥, 沈士明. 流体力学因素对液固两相流冲刷腐蚀的影响[J]. 石油化工设备, 2006, 35(6): 20-23.
【2】DAI Z,SHEN S M,DING G Q. Erosion-corrosion and protection of metals in fluids with solid particles[J]. Corros Prot,2007,28(2): 86.
【3】曹学文, 胥锟, 彭文山. 弯管液固两相流冲蚀失效模拟分析[J]. 表面技术, 2016, 45(8): 124-131.
【4】张德良. 计算流体力学教程[M]. 北京: 高等教育出版社, 2010.
【5】彭文山,曹学文. 固体颗粒对液/固两相流弯管冲蚀作用分析[J]. 中国腐蚀与防护学报,2015,35(6):556-562.
【6】MOISEEV N N, PETROV A A. The calculation of free oscillations of a liquid in a motionless container[J]. Advances in Applied Mechanics, 1966, 9:91-154.
【7】黄卫星,李建明,肖泽仪,等.工程流体力学[M]. 北京:化学工业出版社,2008.
【8】偶国富, 许根富, 朱祖超, 等. 弯管冲蚀失效流固耦合机理及数值模拟[J]. 机械工程学报, 2009, 45(11): 119-124,132.
【9】JOHN FINNEMORE E, JOSEPH B F. 流体力学及其工程应用:英文版[M]. 北京: 机械工业出版社, 2013.
【10】DING Y G,WANG H L, GUO X P, et al. Erosion-corrosion of metals and alloys in liquid-solid phase[J]. Mater Prot,2001,34(11):16.
【11】周三平,艾轮. 弯管处液固两相流体流场数值模拟研究[J]. 化工技术与开发,2016,45(1):39-41.
【12】江春波,张永良,丁则平,等. 计算流体力学[M]. 北京:中国电力出版社,2007.
【13】张孟昀,马贵阳,李存磊,等. 弯管与盲通管冲蚀磨损对比分析研究[J]. 中国安全生产科学技术,2017,13(3):76-81.
【14】柳成文,毛靖儒,俞茂铮,等. 90°弯管内稀疏气固两相流及固粒对壁面磨损量的数值研究[J]. 西安交通大学学报,1999,33(9):53-57.
【15】张继军, 曹会敏, 张少峰. 弯管中液固两相流固粒对壁面磨损的数值模拟[J]. 石油和化工设备, 2008, 11(1): 4-8.
【16】冯进, 张慢来, 冯仲. 带粒液流中圆形弯管的冲蚀模型研究[J]. 长江大学学报(自然科学版)理工卷, 2008, 5(3): 74-76, 80, 386-387.
【17】彭文山, 曹学文, 吉俊毅, 等. 油水砂多相流中固体颗粒对弯管及T型堵头管的冲蚀[J]. 腐蚀与防护, 2016, 37(2): 131-136, 174.
【18】黄勇, 蒋晓东, 施哲雄. 弯头的冲蚀问题及其预测和预防[J]. 炼油技术与工程, 2005, 35(2): 33-36.
【19】丁矿, 朱宏武, 张建华, 等. 直角弯管内液固两相流固体颗粒冲蚀磨损分析[J]. 油气储运, 2013, 32(3): 241-246.
【2】DAI Z,SHEN S M,DING G Q. Erosion-corrosion and protection of metals in fluids with solid particles[J]. Corros Prot,2007,28(2): 86.
【3】曹学文, 胥锟, 彭文山. 弯管液固两相流冲蚀失效模拟分析[J]. 表面技术, 2016, 45(8): 124-131.
【4】张德良. 计算流体力学教程[M]. 北京: 高等教育出版社, 2010.
【5】彭文山,曹学文. 固体颗粒对液/固两相流弯管冲蚀作用分析[J]. 中国腐蚀与防护学报,2015,35(6):556-562.
【6】MOISEEV N N, PETROV A A. The calculation of free oscillations of a liquid in a motionless container[J]. Advances in Applied Mechanics, 1966, 9:91-154.
【7】黄卫星,李建明,肖泽仪,等.工程流体力学[M]. 北京:化学工业出版社,2008.
【8】偶国富, 许根富, 朱祖超, 等. 弯管冲蚀失效流固耦合机理及数值模拟[J]. 机械工程学报, 2009, 45(11): 119-124,132.
【9】JOHN FINNEMORE E, JOSEPH B F. 流体力学及其工程应用:英文版[M]. 北京: 机械工业出版社, 2013.
【10】DING Y G,WANG H L, GUO X P, et al. Erosion-corrosion of metals and alloys in liquid-solid phase[J]. Mater Prot,2001,34(11):16.
【11】周三平,艾轮. 弯管处液固两相流体流场数值模拟研究[J]. 化工技术与开发,2016,45(1):39-41.
【12】江春波,张永良,丁则平,等. 计算流体力学[M]. 北京:中国电力出版社,2007.
【13】张孟昀,马贵阳,李存磊,等. 弯管与盲通管冲蚀磨损对比分析研究[J]. 中国安全生产科学技术,2017,13(3):76-81.
【14】柳成文,毛靖儒,俞茂铮,等. 90°弯管内稀疏气固两相流及固粒对壁面磨损量的数值研究[J]. 西安交通大学学报,1999,33(9):53-57.
【15】张继军, 曹会敏, 张少峰. 弯管中液固两相流固粒对壁面磨损的数值模拟[J]. 石油和化工设备, 2008, 11(1): 4-8.
【16】冯进, 张慢来, 冯仲. 带粒液流中圆形弯管的冲蚀模型研究[J]. 长江大学学报(自然科学版)理工卷, 2008, 5(3): 74-76, 80, 386-387.
【17】彭文山, 曹学文, 吉俊毅, 等. 油水砂多相流中固体颗粒对弯管及T型堵头管的冲蚀[J]. 腐蚀与防护, 2016, 37(2): 131-136, 174.
【18】黄勇, 蒋晓东, 施哲雄. 弯头的冲蚀问题及其预测和预防[J]. 炼油技术与工程, 2005, 35(2): 33-36.
【19】丁矿, 朱宏武, 张建华, 等. 直角弯管内液固两相流固体颗粒冲蚀磨损分析[J]. 油气储运, 2013, 32(3): 241-246.
相关信息