Eddy current array testing of superconducting cable stainless steel sheath weld
摘 要
针对常规无损检测方法无法满足超导电缆不锈钢护套焊缝检测要求以及较高检测效率要求的问题,采用涡流阵列检测技术对电缆不锈钢护套焊缝进行检测,通过研究检测频率、提离效应等对检测信号的影响,确定适用于薄壁不锈钢护套焊缝检测的涡流阵列检测工艺,分别在带有人工缺陷和自然缺陷的试样上进行工艺验证,同时采用X射线和工业计算机层析成像等检测方法验证涡流阵列检测工艺的有效性,为后续实现超导电缆不锈钢护套焊缝的在线实时检测提供依据。
Abstract
Aiming at the problem that conventional nondestructive testing methods cannot meet the inspection requirements of superconducting cable stainless steel weld and the higher inspection efficiency requirements, the eddy current array testing is used to detect the weld of the cable stainless steel pipe. By studying the testing frequency and lift-off effect on the detection signal, it was determined that the eddy current array detection process was suitable for thin-walled stainless steel sheath weld detection. Process verification on the specimens with artificial and natural defects was performed, and the X-ray and industrial computed tomography methods were adopted to verify the validity of the eddy current array testing results. Present work can provide a basis for the subsequent realization of online real-time testing of superconducting cable stainless steel sheath weld.
中图分类号 TG115.28 DOI 10.11973/wsjc202010002
所属栏目 试验研究
基金项目 上海市无损检测专业技术服务平台资助项目(19DZ2293600)
收稿日期 2020/7/23
修改稿日期
网络出版日期
作者单位点击查看
备注张义凤(1978—),女,博士,高级工程师,主要从事先进无损检测技术研究工作
引用该论文: ZHANG Yifeng. Eddy current array testing of superconducting cable stainless steel sheath weld[J]. Nondestructive Testing, 2020, 42(10): 4~9
张义凤. 超导电缆不锈钢护套焊缝的涡流阵列检测[J]. 无损检测, 2020, 42(10): 4~9
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】陆恩万,韩云武. 电缆金属波纹管护套的压力伸长特性的计算[J]. 电线电缆,2020(3):10-12.
【2】王志刚,杨波,李茂东. 基于涡流阵列检测技术的奥氏体不锈钢压力管道缺陷判别方法研究[J]. 传感技术学报,2018,31(11):1733-1738.
【3】吴振成,李来平,涂俊. 铝合金搅拌摩擦焊焊接接头的涡流阵列检测[J]. 无损检测,2018,40(1):25-28.
【4】杨洪斌,仝茂峰,吴晓龙. 发电机风扇叶片的柔性阵列涡流检测[J]. 无损检测,2020,42(2):42-47.
【5】李运涛,宋成,胡斌. 奥氏体不锈钢均匀表面的涡流阵列检测技术应用[J]. 无损检测,2018,40(12):68-73.
【6】张一平,罗雄,杨开宇. 涡流阵列技术在焊缝检测上的应用初探[J]. 中国特种设备安全检测技术,2018,34(3):42-46.
【2】王志刚,杨波,李茂东. 基于涡流阵列检测技术的奥氏体不锈钢压力管道缺陷判别方法研究[J]. 传感技术学报,2018,31(11):1733-1738.
【3】吴振成,李来平,涂俊. 铝合金搅拌摩擦焊焊接接头的涡流阵列检测[J]. 无损检测,2018,40(1):25-28.
【4】杨洪斌,仝茂峰,吴晓龙. 发电机风扇叶片的柔性阵列涡流检测[J]. 无损检测,2020,42(2):42-47.
【5】李运涛,宋成,胡斌. 奥氏体不锈钢均匀表面的涡流阵列检测技术应用[J]. 无损检测,2018,40(12):68-73.
【6】张一平,罗雄,杨开宇. 涡流阵列技术在焊缝检测上的应用初探[J]. 中国特种设备安全检测技术,2018,34(3):42-46.
相关信息