Pulsed eddy current thickness measurement and characteristic extraction of ferromagnetic materials
摘 要
基于COMSOL Multiphysics软件,利用有限元法建立了脉冲涡流检测铁磁性试件厚度的仿真模型,通过改变试件厚度参数进行仿真试验,得到了不同厚度所对应的检测电压信号。最后,分别以差分电压信号峰值、差分电压信号峰值时间及单对数坐标系下晚期信号斜率为特征量进行了壁厚反演,比较了3种特征量反演壁厚的范围和特点。
Abstract
Based on the COMSOL Multiphysics software, the simulation model of the thickness of the ferromagnetic test piece for pulsed eddy current testing was established by using the finite element method. Then the thickness of the tested piece was changed to simulate the experiment, and the detection voltage signals corresponding to different thicknesses were obtained. Finally, the wall thickness inversion is realized by the peak value of the differential voltage signal, the peak time of the differential voltage signal and the slope of the late signal in the single logarithmic coordinate system. The range and characteristics of the wall thickness of the three feature quantities are compared.
中图分类号 TG115.28 DOI 10.11973/wsjc202011008
所属栏目 试验研究
基金项目 国家重点研发计划资助项目(2016YFC0802302)
收稿日期 2020/4/26
修改稿日期
网络出版日期
作者单位点击查看
联系人作者王安泉(10257217@qq.com)
备注王安泉(1979-),男,高级工程师,主要从事设备的无损检测工作
引用该论文: WANG Anquan,CHEN Jianfei,YANG Yong,HAN Qing,GONG Hao,YAN Taisong. Pulsed eddy current thickness measurement and characteristic extraction of ferromagnetic materials[J]. Nondestructive Testing, 2020, 42(11): 38~41
王安泉,陈健飞,杨勇,韩庆,宫昊,闫泰松. 铁磁性材料的脉冲涡流测厚与特征量提取[J]. 无损检测, 2020, 42(11): 38~41
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】薛盛龙, 付跃文,顾增涛.周边管道对带包覆层管道脉冲涡流检测的影响[J].无损检测,2016,38(3):1-4.
【2】FAN Mengbao,CAO Binghua,YANG Panpan,et al. Elimination of liftoff effect using a Model-Based method for eddy current characterization of a plate[J].NDT&E International,2015,74(9):66-71.
【3】XIE Shejuan,CHEN Zhenmao,TAKAGI T,et al.Quantitative non-destructive evaluation of wall thinning defect in double-layer pipe of nuclear power plants using pulsed ECT method[J].NDT&E International,2015,75:87-95.
【4】徐志远, 武新军,康宜华,等.脉冲涡流检测集总参数模型[J].华中科技大学学报(自然科学版),2013,41(5):1-5.
【5】陈兴乐, 雷银照.平板导体脉冲涡流场时域解与测厚特征量的提取[J].电工技术学报,2013,28(6):1-8.
【6】王志春, 王玉玺.脉冲涡流多层厚度检测与视频特征量提取[J].传感器与微系统,2018,37(1):18-21.
【7】刘丽冰, 刘又午,赵小松,等.加工中心在线检测误差补偿技术研究[J].中国机械工程,2000,11(3):313-316.
【8】GIGURE S, DUBOIS S J M. Pulsed eddy current:finding corrosion independently of transducer lift-off[J]. Review of Progress in Quantitative Nondestructive,2000, 509(1):449-456.
【9】柯海, 徐志远,黄琛,等.基于信号斜率的铁磁材料脉冲涡流测厚研究[J].仪器仪表学报,2011,32(10):2376-2381.
【10】戴光, 李鹏,李良,等.基于脉冲涡流检测的管道腐蚀仿真与实验研究[J].化工设备与管道,2016,53(2):63-75.
【2】FAN Mengbao,CAO Binghua,YANG Panpan,et al. Elimination of liftoff effect using a Model-Based method for eddy current characterization of a plate[J].NDT&E International,2015,74(9):66-71.
【3】XIE Shejuan,CHEN Zhenmao,TAKAGI T,et al.Quantitative non-destructive evaluation of wall thinning defect in double-layer pipe of nuclear power plants using pulsed ECT method[J].NDT&E International,2015,75:87-95.
【4】徐志远, 武新军,康宜华,等.脉冲涡流检测集总参数模型[J].华中科技大学学报(自然科学版),2013,41(5):1-5.
【5】陈兴乐, 雷银照.平板导体脉冲涡流场时域解与测厚特征量的提取[J].电工技术学报,2013,28(6):1-8.
【6】王志春, 王玉玺.脉冲涡流多层厚度检测与视频特征量提取[J].传感器与微系统,2018,37(1):18-21.
【7】刘丽冰, 刘又午,赵小松,等.加工中心在线检测误差补偿技术研究[J].中国机械工程,2000,11(3):313-316.
【8】GIGURE S, DUBOIS S J M. Pulsed eddy current:finding corrosion independently of transducer lift-off[J]. Review of Progress in Quantitative Nondestructive,2000, 509(1):449-456.
【9】柯海, 徐志远,黄琛,等.基于信号斜率的铁磁材料脉冲涡流测厚研究[J].仪器仪表学报,2011,32(10):2376-2381.
【10】戴光, 李鹏,李良,等.基于脉冲涡流检测的管道腐蚀仿真与实验研究[J].化工设备与管道,2016,53(2):63-75.
相关信息