Influence of Specimen Thickness on Charpy Impact Test Results
摘 要
通过不同温度下的夏比摆锤冲击试验对非标准小尺寸V型缺口冲击试样的冲击吸收能量和侧膨胀值进行了分析,并结合力-位移曲线,研究了试样厚度对冲击试验结果的影响。结果表明:当试验温度高于韧脆转变温度时,冲击吸收能量与试样的横截面积有关,因此与厚度呈线性关系;而低于韧脆转变温度时,冲击吸收能量与试样厚度之间没有明显关系;试样的侧膨胀值、剪切断面率与厚度之间没有直接联系。随着试样厚度的减小,不稳定裂纹扩展起始力越来越小,从而导致冲击吸收能量减小。厚度越大试样吸收的能量越多,冲击过程中所受到的最大力也越大。
Abstract
The impact absorbed energy and side expansion value of non-standard small size V-notch impact specimens were analyzed through Charpy pendulum impact test at different temperatures, and the influence of specimen thickness on the impact test results were studied combined with force-displacement curves. The results show that when the test temperature is higher than ductile brittle transition temperature, the impact absorbed energy is related to cross-sectional area of specimen, so it has a linear relationship with the thickness. When the temperature is lower than ductile brittle transition temperature, there is no obvious relationship between the impact absorbed energy and the thickness of specimen. There is no direct relationship between the thickness and the side expansion value, shear section rate of specimen. With the decrease of specimen thickness, the initial force of unstable crack propagation becomes smaller and smaller, which leads to the decrease of impact absorbed energy. The greater the thickness is, the more energy absorbed by specimen and the greater the maximum force in the impact process.
中图分类号 TG115.5 DOI 10.11973/lhjy-wl202103010
所属栏目 试验与研究
基金项目
收稿日期 2020/5/25
修改稿日期
网络出版日期
作者单位点击查看
备注丁阳(1987-),男,工程师,主要从事金属材料的理化检验及机械零件的失效分析工作,dingyang@shanghai-electric.com
引用该论文: DING Yang. Influence of Specimen Thickness on Charpy Impact Test Results[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2021, 57(3): 46~49
丁阳. 试样厚度对夏比冲击试验结果的影响[J]. 理化检验-物理分册, 2021, 57(3): 46~49
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】机械工业理化检验人员技术培训和资格鉴定委员会.力学性能试验[M].北京:中国计量出版社,2008.
【2】方健.落锤撕裂试验的发展及其在评价材料韧断止裂性能中的应用[J].理化检验(物理分册),2015,51(6):381-387.
【3】黎智辉.夏比冲击试样尺寸对试验结果的影响[J].理化检验(物理分册),2013,49(10):664-667.
【4】刘学政,普晓明,敬仕煜,等.夏比V型冲击试验的尺寸效应及工程应用[J].理化检验(物理分册),2020,56(5):1-5.
【5】范立坤. V型缺口冲击试样尺寸公差因素的有限元分析[J].理化检验(物理分册),2014, 50(8):574-577.
【6】郭洋,唐新华,邓胜杰,等.焊接热影响区对SA508Gr. 3钢落锤试验影响研究[J].焊接,2018(7),24-28.
【7】刘丽梅,李金梅,杨莉,等.侧向膨胀值表征材料韧性的基础性研究[J].热处理技术与装备,2019,40(4):52-54.
【2】方健.落锤撕裂试验的发展及其在评价材料韧断止裂性能中的应用[J].理化检验(物理分册),2015,51(6):381-387.
【3】黎智辉.夏比冲击试样尺寸对试验结果的影响[J].理化检验(物理分册),2013,49(10):664-667.
【4】刘学政,普晓明,敬仕煜,等.夏比V型冲击试验的尺寸效应及工程应用[J].理化检验(物理分册),2020,56(5):1-5.
【5】范立坤. V型缺口冲击试样尺寸公差因素的有限元分析[J].理化检验(物理分册),2014, 50(8):574-577.
【6】郭洋,唐新华,邓胜杰,等.焊接热影响区对SA508Gr. 3钢落锤试验影响研究[J].焊接,2018(7),24-28.
【7】刘丽梅,李金梅,杨莉,等.侧向膨胀值表征材料韧性的基础性研究[J].热处理技术与装备,2019,40(4):52-54.
相关信息