Program Segment Design and Test Result of H-beam Tensile Sample Processed by Numerical Control High Speed Sawing Machine
摘 要
为使D-450H型数控高速锯床满足H型钢拉伸试样的加工要求,对该型数控高速锯床的程序段进行设计,并对加工出的H型钢拉伸试样的试验结果进行对比验证试验。结果表明:采用经过程序段设计的数控高速锯床加工出的H型钢拉伸试样在拉伸试验时基本不会发生应变强化;试样尺寸及形状公差均满足标准要求;抗拉强度、屈服强度及断后伸长率与鳄鱼剪剪切试样的基本一致,但其表面粗糙度更小,平均值仅为0.61 \mm,且精度较高。
Abstract
In order to make D-450H numerical control high-speed sawing machine meet the processing requirements of H-beam tensile sample, the program segment of numerical control high-speed sawing machine was designed, the test results of H-beam tensile sample processed by numerical control high-speed sawing machine were compared and verified. The results show that the tensile sample of H-beam processed by numerical control high-speed sawing machine with program segment design basically does not have strain strengthening during tensile test. The dimension and shape tolerance of sample meet the standard requirements. The tensile strength, yield strength and elongation after fracture are basically the same as those of crocodile shear samples, but the surface roughness is smaller, the average value is only 0.61 \mm, and the accuracy is high.
中图分类号 TG115.2 DOI 10.11973/lhjy-wl202107006
所属栏目 试验与研究
基金项目
收稿日期 2020/6/23
修改稿日期
网络出版日期
作者单位点击查看
备注宋小勇(1969-),男,工程师,主要从事钢铁材料力学性能测试工作,2257507692@qq.com
引用该论文: SONG Xiaoyong,CHENG Yanan. Program Segment Design and Test Result of H-beam Tensile Sample Processed by Numerical Control High Speed Sawing Machine[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2021, 57(7): 25~28
宋小勇,程亚南. 数控高速锯床加工H型钢拉伸试样的程序段设计及试验结果[J]. 理化检验-物理分册, 2021, 57(7): 25~28
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】陈海烽. 金属切削带锯床数控锯切系统研究[D].杭州:浙江工业大学,2014.
【2】贾欣.碳素结构钢拉伸比对试验样坯制备及均匀性检查[J].江苏冶金,2006,34(2):27-30.
【3】李彦军,陈彬,亓建,等.试样机加工对金属拉伸试验结果的影响[J].物理测试,2011,29(2):26-29.
【4】于爱民,林梦桥,王景.拉伸试样加工方法对厚规格延伸性能的影响[J].河南冶金,2012,20(2):23-25.
【5】巴虹.拉伸试样尺寸精度对拉伸试验结果的影响[J].鞍钢技术,2001(4):72-73.
【2】贾欣.碳素结构钢拉伸比对试验样坯制备及均匀性检查[J].江苏冶金,2006,34(2):27-30.
【3】李彦军,陈彬,亓建,等.试样机加工对金属拉伸试验结果的影响[J].物理测试,2011,29(2):26-29.
【4】于爱民,林梦桥,王景.拉伸试样加工方法对厚规格延伸性能的影响[J].河南冶金,2012,20(2):23-25.
【5】巴虹.拉伸试样尺寸精度对拉伸试验结果的影响[J].鞍钢技术,2001(4):72-73.
相关信息