Reasons of Low Room Temperature Tensile Strength of TC4 Titanium Alloy Bar
摘 要
通过化学成分分析、硬度试验、室温拉伸试验以及显微组织观察等方法,分析了TC4钛合金棒材室温拉伸强度偏低的原因。结果表明:TC4钛合金棒材室温下的抗拉强度和屈服强度偏低的主要原因是其热处理工艺中的冷却方式为炉冷,冷却速率较慢,导致其初生α相含量较高,且出现了少量较宽的短棒状次生α相。
Abstract
Through chemical composition analysis, hardness test, room temperature tensile test and microstructure observation and other mehtods, the reasons for low room temperature tensile strength of TC4 titanium alloy bar were analyzed. The results showed that the main reason for low tensile strength and yield strength of TC4 titanium alloy bar at room temperature was that the cooling method in heat treatment process was furnace cooling, and the cooling speed was slow, which resulted in a high content of primary α phase and a small amount of short rod secondary α phase with wide width.
中图分类号 TG142.1 DOI 10. 11973/lhjy-wl202111002
所属栏目 试验与研究
基金项目
收稿日期 2020/5/25
修改稿日期
网络出版日期
作者单位点击查看
备注王萱(1992-),女,助理工程师,主要从事钛金属力学性能研究,1411210447@qq.com
引用该论文: WANG Xuan,LIU Hongwei,ZHAO Hui,LI Chao,XU Junmei,LI Zhenting. Reasons of Low Room Temperature Tensile Strength of TC4 Titanium Alloy Bar[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2021, 57(11): 6~9
王萱,刘宏伟,赵辉,李超,徐军梅,李贞婷. TC4钛合金棒材室温拉伸强度偏低的原因[J]. 理化检验-物理分册, 2021, 57(11): 6~9
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】李桂荣, 王芳芳, 王宏明, 等.脉冲强磁场拉伸时TC4钛合金的塑变能力和微观组织[J]. 稀有金属材料与工程, 2018, 47(4):1119-1123.
【2】王琦.TC4钛合金的低温拉伸性能[J]. 材料工程, 2009, 37(3):54-55, 61.
【3】WU B Y, XIONG S B, GUO Y Q, et al. Tooth-colored bioactive titanium alloy prepared with anodic oxidation method for dental implant application[J]. Materials Letters, 2019, 248:134-137.
【4】XIE R Z, LIN N M, ZHOU P, et al. Surface damage mitigation of TC4 alloy via micro arc oxidation for oil and gas exploitation application:Characterizations of microstructure and evaluations on surface performance[J]. Applied Surface Science, 2018, 436:467-476.
【5】于振涛, 余森, 程军, 等.新型医用钛合金材料的研发和应用现状[J]. 金属学报, 2017, 53(10):1238-1264.
【6】吕钢, 董尚利, 王庆民, 等.热循环对TC4合金室温和低温拉伸性能的影响[J]. 材料热处理学报, 2009, 30(2):36-38.
【7】高禹, 何世禹, 杨德庄, 等.低温对时效态TC4合金拉伸性能的影响[J]. 材料科学与工艺, 2002, 10(4):352-356.
【8】丁嘉健, 刘家和, 杨展铭, 等.TC4钛合金板材高温热拉伸性能的研究[J]. 科技创新与应用, 2019(11):41-42, 45.
【9】姚良, 徐浩杰, 刘丽.双自封高液压气管接头开裂原因分析[J]. 理化检验(物理分册), 2019, 55(9):643-645.
【10】张凤林.现场布氏硬度检测技术[J]. 理化检验(物理分册), 2015, 51(12):845-852.
【11】陈亚军, 周姝, 白云.民航维修领域金属材料洛氏硬度检测标准的对比分析[J]. 理化检验(物理分册), 2015, 51(9):636-642.
【12】王涛, 荆洪阳, 徐连勇, 等.基于里氏硬度测量的P92钢及焊缝布氏硬度的计算[J]. 焊接学报, 2016, 37(9):87-90, 132.
【13】王建萍, 王家平, 许建广.数字图像处理在定量金相分析中的应用[J]. 材料导报, 2003, 17(1):63-65, 77.
【14】NEERAJ T, HOU D H, DAEHN G S, et al. Phenomenological and microstructural analysis of room temperature creep in titanium alloys[J]. Acta Materialia, 2000, 48(6):1225-1238.
【15】刘建强.TC4钛合金的显微组织及其抗冲击韧性[J]. 热加工工艺, 2013, 42(12):63-66.
【16】孙远东.布氏硬度与抗拉强度的相关性在质控中的应用[J]. 兵器材料科学与工程, 2019, 42(2):92-95.
【2】王琦.TC4钛合金的低温拉伸性能[J]. 材料工程, 2009, 37(3):54-55, 61.
【3】WU B Y, XIONG S B, GUO Y Q, et al. Tooth-colored bioactive titanium alloy prepared with anodic oxidation method for dental implant application[J]. Materials Letters, 2019, 248:134-137.
【4】XIE R Z, LIN N M, ZHOU P, et al. Surface damage mitigation of TC4 alloy via micro arc oxidation for oil and gas exploitation application:Characterizations of microstructure and evaluations on surface performance[J]. Applied Surface Science, 2018, 436:467-476.
【5】于振涛, 余森, 程军, 等.新型医用钛合金材料的研发和应用现状[J]. 金属学报, 2017, 53(10):1238-1264.
【6】吕钢, 董尚利, 王庆民, 等.热循环对TC4合金室温和低温拉伸性能的影响[J]. 材料热处理学报, 2009, 30(2):36-38.
【7】高禹, 何世禹, 杨德庄, 等.低温对时效态TC4合金拉伸性能的影响[J]. 材料科学与工艺, 2002, 10(4):352-356.
【8】丁嘉健, 刘家和, 杨展铭, 等.TC4钛合金板材高温热拉伸性能的研究[J]. 科技创新与应用, 2019(11):41-42, 45.
【9】姚良, 徐浩杰, 刘丽.双自封高液压气管接头开裂原因分析[J]. 理化检验(物理分册), 2019, 55(9):643-645.
【10】张凤林.现场布氏硬度检测技术[J]. 理化检验(物理分册), 2015, 51(12):845-852.
【11】陈亚军, 周姝, 白云.民航维修领域金属材料洛氏硬度检测标准的对比分析[J]. 理化检验(物理分册), 2015, 51(9):636-642.
【12】王涛, 荆洪阳, 徐连勇, 等.基于里氏硬度测量的P92钢及焊缝布氏硬度的计算[J]. 焊接学报, 2016, 37(9):87-90, 132.
【13】王建萍, 王家平, 许建广.数字图像处理在定量金相分析中的应用[J]. 材料导报, 2003, 17(1):63-65, 77.
【14】NEERAJ T, HOU D H, DAEHN G S, et al. Phenomenological and microstructural analysis of room temperature creep in titanium alloys[J]. Acta Materialia, 2000, 48(6):1225-1238.
【15】刘建强.TC4钛合金的显微组织及其抗冲击韧性[J]. 热加工工艺, 2013, 42(12):63-66.
【16】孙远东.布氏硬度与抗拉强度的相关性在质控中的应用[J]. 兵器材料科学与工程, 2019, 42(2):92-95.
相关信息