Verification of some technical problems in ISO 10113:2020 standard
摘 要
详细介绍了全国钢标委组织相关单位开展的ISO 10113:2020标准验证工作。主要对人工、半自动和全自动3种测试方式的准确性和一致性进行验证,此外还对试样是否存在不均匀变形以及是否需要在计算公式中去除弹性应变等问题进行了试验。验证试验可以让相关人员更加清晰、全面地认识该标准中的一些关键条文,为下一步启动修订GB/T 5027—2016标准的工作打下良好基础,同时对推动国内塑性应变比(r值)测试技术的发展,促进国内装备水平的提高具有重要意义。
Abstract
The verification work of ISO 10113:2020 standard organized by National Steel Standardization Committee was introduced in detail. The accuracy and consistency of manual, semi-automatic and automatic test methods were mainly verified. In addition, a series of tests were carried out on whether the specimen had uneven deformation and whether it was necessary to avoid elastic strain. The verification test could make the related personnel more clearly and comprehensively understand some key provisions in the standard, which layed a good foundation for the next step to start the revision of GB/T 5027—2016 standard. At the same time, it was of great significance to promote the development of domestic the plastic strain ration (r value) test technology and the improvement of domestic equipment level.
中图分类号 TB31 TG113.25 DOI 10.11973/lhjy-wl202202002
所属栏目 专题报道(塑性应变比的检验方法)
基金项目
收稿日期 2021/9/25
修改稿日期
网络出版日期
作者单位点击查看
备注凃应宏(1970-),男,高级工程师,主要从事力学性能检测工作,E06036@baosteel.com
引用该论文: TU Yinghong,LI Rongfeng,SHANG Lun. Verification of some technical problems in ISO 10113:2020 standard[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2022, 58(2): 4~11
凃应宏,李荣锋,尚伦. ISO 10113:2020标准中若干技术问题的验证[J]. 理化检验-物理分册, 2022, 58(2): 4~11
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】梁新邦.金属塑性应变比r值测定方法误差分析[J].理化检验(物理分册), 2000, 36(5):209-212.
【2】苏大雄, 徐惟诚, 李和平, 等.金属薄板塑性应变比(r值)测试的影响因素分析[J].理化检验(物理分册), 2006, 42(3):113-115.
【3】孙志鹏, 徐雁, 宋祖峰.拉伸试验机r值异常的具体表现及原因分析[J].物理测试, 2020, 38(1):24-27.
【4】方健, 魏毅静, 范朝晖.拉伸试验的验证比对与延塑性指标能力分析[J].塑性工程学报, 2007, 14(2):1-6.
【5】陈光南.r值n值试验方法国家标准起草中的若干问题及试验结论[J].钢铁研究, 1985, 13(1):38-43.
【2】苏大雄, 徐惟诚, 李和平, 等.金属薄板塑性应变比(r值)测试的影响因素分析[J].理化检验(物理分册), 2006, 42(3):113-115.
【3】孙志鹏, 徐雁, 宋祖峰.拉伸试验机r值异常的具体表现及原因分析[J].物理测试, 2020, 38(1):24-27.
【4】方健, 魏毅静, 范朝晖.拉伸试验的验证比对与延塑性指标能力分析[J].塑性工程学报, 2007, 14(2):1-6.
【5】陈光南.r值n值试验方法国家标准起草中的若干问题及试验结论[J].钢铁研究, 1985, 13(1):38-43.
相关信息