Mechanical Property Changes of Tungsten after Helium Ion Irradiation with Different Damage Degree
摘 要
采用不同能量和束流的氦离子对再结晶钨表面进行辐照试验,对辐照损伤分别为0.2,0.5,1.0 dpa下钨的微观形貌进行观察,并采用不同半径(1,5,10 μm)球形压头对其进行纳米压痕试验,获得压痕应力-应变曲线,探究其力学性能的变化及原因。结果表明:不同损伤程度辐照后钨表面损伤层的厚度为554~558 nm;随着辐照损伤程度的加剧,钨中位错环密度明显增大;辐照后钨的压痕应力-应变曲线均未出现突跳现象,且随着辐照损伤程度的增加,屈服强度提高,压痕弹性模量基本保持不变,辐照后产生的位错环缺陷是引起钨力学性能发生变化的直接原因;钨的力学性能具有压痕尺寸效应,压头半径越小,钨的屈服强度越高,未辐照钨的压痕应力-应变曲线出现突跳现象时的压痕应力越大。
Abstract
The surface of recrystallized tungsten was irradiated by helium ions with different energy and ion fluence. The microstructure of tungsten with irradiation damage of 0.2,0.5,1.0 dpa was observed. The nanoindentation test was conducted with spherical indenter of different radius (1,5,10 μm) to obtain the indentation stress-strain curve, and the change of mechanical properties and reason for the change were explored. The results show that the thickness of damage layer on tungsten surface was 554-558 nm after irradiation with different damage degree. With increasing damage degree, the density of dislocation loop in tungsten increased obviously. The indentation stress-strain curves of tungsten after irradiation did not exhibit pop-in phenomenon, and the yield strength increased with damage degree, and the indentation elastic modulus basically unchanged. The dislocation loop defect caused by irradiation was the direct cause of the change of mechanical properties of tungsten. The mechanical properties of tungsten had the effect of indentation size. The smaller the indenter radius, the higher the yield strength of tungsten, and the greater the indentation stress when the stress-strain curve of unirradiated tungsten showed pop-in.
中图分类号 TG146.4+11 TL62+7 DOI 10.11973/jxgccl202204004
所属栏目 试验研究
基金项目 国家自然科学基金资助项目(51971115)
收稿日期 2021/8/17
修改稿日期 2022/3/3
网络出版日期
作者单位点击查看
备注陈婉琦(1993-)女,辽宁鞍山人,工程师,博士
引用该论文: CHEN Wanqi,LI Xinnan,LI Kailun,CHIU Yulung,LIU Wei. Mechanical Property Changes of Tungsten after Helium Ion Irradiation with Different Damage Degree[J]. Materials for mechancial engineering, 2022, 46(4): 26~31
陈婉琦,李馨楠,李恺伦,CHIUYulung,刘伟. 钨在不同损伤程度氦离子辐照后的力学性能变化[J]. 机械工程材料, 2022, 46(4): 26~31
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】ONGENA J, VAN OOST G.Energy for future centuries:Prospects for fusion power as a future energy source[J].Fusion Science and Technology, 2010, 57(2T):3-15.
【2】GILBERT M R, DUDAREV S L, ZHENG S, et al.An integrated model for materials in a fusion power plant:Transmutation, gas production, and helium embrittlement under neutron irradiation[J].Nuclear Fusion, 2012, 52(8):083019.
【3】HIRAI T, ESCOURBIAC F, CARPENTIER-CHOUCHANA S, et al.ITER full tungsten divertor qualification program and progress[J].Physica Scripta, 2014, T159:014006.
【4】KAJITA S, SAKAGUCHI W, OHNO N, et al.Formation process of tungsten nanostructure by the exposure to helium plasma under fusion relevant plasma conditions[J].Nuclear Fusion, 2009, 49(9):095005.
【5】OU X, ANWAND W, KÖGLER R, et al.The role of helium implantation induced vacancy defect on hardening of tungsten[J].Journal of Applied Physics, 2014, 115(12):123521.
【6】DEBELLE A, BARTHE M F, SAUVAGE T.First temperature stage evolution of irradiation-induced defects in tungsten studied by positron annihilation spectroscopy[J].Journal of Nuclear Materials, 2008, 376(2):216-221.
【7】PATHAK S, KALIDINDI S R.Spherical nanoindentation stress-strain curves[J].Materials Science and Engineering:R:Reports, 2015, 91:1-36.
【8】BUSHBY A J, ROBERTS S G, HARDIE C D.Nanoindentation investigation of ion-irradiated Fe-Cr alloys using spherical indenters[J].Journal of Materials Research, 2012, 27(1):85-90.
【9】WEAVER J S, PATHAK S, REICHARDT A, et al.Spherical nanoindentation of proton irradiated 304 stainless steel:A comparison of small scale mechanical test techniques for measuring irradiation hardening[J].Journal of Nuclear Materials, 2017, 493:368-379.
【10】PATHAK S, KALIDINDI S R, WEAVER J S, et al.Probing nanoscale damage gradients in ion-irradiated metals using spherical nanoindentation[J].Scientific Reports, 2017, 7:11918.
【11】ZIEGLER J F, ZIEGLER M D, BIERSACK J P.SRIM-The stopping and range of ions in matter (2010)[J].Nuclear Instruments and Methods in Physics Research Section B:Beam Interactions With Materials and Atoms, 2010, 268(11/12):1818-1823.
【12】OLIVER W C, PHARR G M.Measurement of hardness and elastic modulus by instrumented indentation:Advances in understanding and refinements to methodology[J].Journal of Materials Research, 2004, 19(1):3-20.
【13】HERTZ H.Miscellaneous papers[J].Archives of Andrology, 2009, 11(3):197-222.
【14】王康, 邓爱红, 龚敏, 等.多能氦离子注入对W金属微结构的影响[J].金属学报, 2017(1):70-76. WANG K, DENG A H, GONG M, et al.Effect on microstructure of tungsten under helium ions irradiation with multiple energy[J].Acta Metallurgica Sinica, 2017(1):70-76.
【15】PATHAK S, RIESTERER J L, KALIDINDI S R, et al.Understanding pop-ins in spherical nanoindentation[J].Applied Physics Letters, 2014, 105(16):161913.
【16】CHEN W Q, WANG X Y, XIAO X Z, et al.Characterization of dose dependent mechanical properties in helium implanted tungsten[J].Journal of Nuclear Materials, 2018, 509:260-266.
【17】ZHAO M Z, LIU F, YANG Z S, et al.Fluence dependence of helium ion irradiation effects on the microstructure and mechanical properties of tungsten[J].Nuclear Instruments and Methods in Physics Research Section B:Beam Interactions With Materials and Atoms, 2018, 414:121-125.
【18】ZINKLE S J, MATSUKAWA Y.Observation and analysis of defect cluster production and interactions with dislocations[J].Journal of Nuclear Materials, 2004, 329/330/331/332/333:88-96.
【19】TAN L, BUSBY J T.Formulating the strength factor α for improved predictability of radiation hardening[J].Journal of Nuclear Materials, 2015, 465:724-730.
【20】TAYLOR G I. Plastic deformation of crystals[J]. Proceedings of the Royal Society of London, 1934, 145:362-404.
【21】TAYLOR G I. Plastic strain in metals[J]. Journal of the Institute of Metals, 1938, 62:307-324.
【22】QU S, HUANG Y, NIX W D, et al.Indenter tip radius effect on the Nix-Gao relation in micro-and nanoindentation hardness experiments[J].Journal of Materials Research, 2004, 19(11):3423-3434.
【23】WEAVER J S, SUN C, WANG Y Q, et al.Quantifying the mechanical effects of He, W and He+W ion irradiation on tungsten with spherical nanoindentation[J].Journal of Materials Science, 2018, 53(7):5296-5316.
【24】ARSENLIS A, PARKS D M.Crystallographic aspects of geometrically-necessary and statistically-stored dislocation density[J].Acta Materialia, 1999, 47(5):1597-1611.
【25】GAO H J, HUANG Y G.Geometrically necessary dislocation and size-dependent plasticity[J].Scripta Materialia, 2003, 48(2):113-118.
【26】CLEVERINGA H, VAN DER GIESSEN E, NEEDLEMAN A.Discrete dislocation simulations and size dependent hardening in single slip[J].Le Journal De Physique IV, 1998, 8(PR4):Pr4-83.
【27】CLEVERINGA H H M, GIESSEN E V D, NEEDLEMAN A.Comparison of discrete dislocation and continuum plasticity predictions for a composite material[J].Acta Materialia, 1997, 45(8):3163-3179.
【2】GILBERT M R, DUDAREV S L, ZHENG S, et al.An integrated model for materials in a fusion power plant:Transmutation, gas production, and helium embrittlement under neutron irradiation[J].Nuclear Fusion, 2012, 52(8):083019.
【3】HIRAI T, ESCOURBIAC F, CARPENTIER-CHOUCHANA S, et al.ITER full tungsten divertor qualification program and progress[J].Physica Scripta, 2014, T159:014006.
【4】KAJITA S, SAKAGUCHI W, OHNO N, et al.Formation process of tungsten nanostructure by the exposure to helium plasma under fusion relevant plasma conditions[J].Nuclear Fusion, 2009, 49(9):095005.
【5】OU X, ANWAND W, KÖGLER R, et al.The role of helium implantation induced vacancy defect on hardening of tungsten[J].Journal of Applied Physics, 2014, 115(12):123521.
【6】DEBELLE A, BARTHE M F, SAUVAGE T.First temperature stage evolution of irradiation-induced defects in tungsten studied by positron annihilation spectroscopy[J].Journal of Nuclear Materials, 2008, 376(2):216-221.
【7】PATHAK S, KALIDINDI S R.Spherical nanoindentation stress-strain curves[J].Materials Science and Engineering:R:Reports, 2015, 91:1-36.
【8】BUSHBY A J, ROBERTS S G, HARDIE C D.Nanoindentation investigation of ion-irradiated Fe-Cr alloys using spherical indenters[J].Journal of Materials Research, 2012, 27(1):85-90.
【9】WEAVER J S, PATHAK S, REICHARDT A, et al.Spherical nanoindentation of proton irradiated 304 stainless steel:A comparison of small scale mechanical test techniques for measuring irradiation hardening[J].Journal of Nuclear Materials, 2017, 493:368-379.
【10】PATHAK S, KALIDINDI S R, WEAVER J S, et al.Probing nanoscale damage gradients in ion-irradiated metals using spherical nanoindentation[J].Scientific Reports, 2017, 7:11918.
【11】ZIEGLER J F, ZIEGLER M D, BIERSACK J P.SRIM-The stopping and range of ions in matter (2010)[J].Nuclear Instruments and Methods in Physics Research Section B:Beam Interactions With Materials and Atoms, 2010, 268(11/12):1818-1823.
【12】OLIVER W C, PHARR G M.Measurement of hardness and elastic modulus by instrumented indentation:Advances in understanding and refinements to methodology[J].Journal of Materials Research, 2004, 19(1):3-20.
【13】HERTZ H.Miscellaneous papers[J].Archives of Andrology, 2009, 11(3):197-222.
【14】王康, 邓爱红, 龚敏, 等.多能氦离子注入对W金属微结构的影响[J].金属学报, 2017(1):70-76. WANG K, DENG A H, GONG M, et al.Effect on microstructure of tungsten under helium ions irradiation with multiple energy[J].Acta Metallurgica Sinica, 2017(1):70-76.
【15】PATHAK S, RIESTERER J L, KALIDINDI S R, et al.Understanding pop-ins in spherical nanoindentation[J].Applied Physics Letters, 2014, 105(16):161913.
【16】CHEN W Q, WANG X Y, XIAO X Z, et al.Characterization of dose dependent mechanical properties in helium implanted tungsten[J].Journal of Nuclear Materials, 2018, 509:260-266.
【17】ZHAO M Z, LIU F, YANG Z S, et al.Fluence dependence of helium ion irradiation effects on the microstructure and mechanical properties of tungsten[J].Nuclear Instruments and Methods in Physics Research Section B:Beam Interactions With Materials and Atoms, 2018, 414:121-125.
【18】ZINKLE S J, MATSUKAWA Y.Observation and analysis of defect cluster production and interactions with dislocations[J].Journal of Nuclear Materials, 2004, 329/330/331/332/333:88-96.
【19】TAN L, BUSBY J T.Formulating the strength factor α for improved predictability of radiation hardening[J].Journal of Nuclear Materials, 2015, 465:724-730.
【20】TAYLOR G I. Plastic deformation of crystals[J]. Proceedings of the Royal Society of London, 1934, 145:362-404.
【21】TAYLOR G I. Plastic strain in metals[J]. Journal of the Institute of Metals, 1938, 62:307-324.
【22】QU S, HUANG Y, NIX W D, et al.Indenter tip radius effect on the Nix-Gao relation in micro-and nanoindentation hardness experiments[J].Journal of Materials Research, 2004, 19(11):3423-3434.
【23】WEAVER J S, SUN C, WANG Y Q, et al.Quantifying the mechanical effects of He, W and He+W ion irradiation on tungsten with spherical nanoindentation[J].Journal of Materials Science, 2018, 53(7):5296-5316.
【24】ARSENLIS A, PARKS D M.Crystallographic aspects of geometrically-necessary and statistically-stored dislocation density[J].Acta Materialia, 1999, 47(5):1597-1611.
【25】GAO H J, HUANG Y G.Geometrically necessary dislocation and size-dependent plasticity[J].Scripta Materialia, 2003, 48(2):113-118.
【26】CLEVERINGA H, VAN DER GIESSEN E, NEEDLEMAN A.Discrete dislocation simulations and size dependent hardening in single slip[J].Le Journal De Physique IV, 1998, 8(PR4):Pr4-83.
【27】CLEVERINGA H H M, GIESSEN E V D, NEEDLEMAN A.Comparison of discrete dislocation and continuum plasticity predictions for a composite material[J].Acta Materialia, 1997, 45(8):3163-3179.
相关信息