搜索热:失效分析 陶瓷
扫一扫 加微信
首页 > 期刊论文 > 论文摘要
(Sm0.5Nd0.5)3Ce7Ta2O23.5和(Yb0.5Dy0.5)3Ce7Ta2O23.5氧化物的热物理性能
          
Thermophysical Performances of (Sm0.5Nd0.5)3Ce7Ta2O23.5 and(Yb0.5Dy0.5)3Ce7Ta2O23.5 Oxides

摘    要
以高纯度Sm2O3、NdO3、Dy2O3、Yb2O3、CeO2和Ta2O5为原材料,采用多步高温固相烧结法制备了(Sm0.5Nd0.5)3Ce7Ta2O23.5和(Yb0.5Dy0.5)3Ce7Ta2O23.5氧化物,研究了其晶体结构、微观形貌、热物理性能等。结果表明:制备的氧化物均具有单一的萤石结构,其结构致密,晶界清晰,元素种类和原子比与化学式基本一致;这2种氧化物的热导率明显低于7YSZ,且(Yb0.5Dy0.5)3Ce7Ta2O23.5的热导率低于(Sm0.5Nd0.5)3Ce7Ta2O23.5的;(Yb0.5Dy0.5)3Ce7Ta2O23.5在900℃以上高温热膨胀系数略高于(Sm0.5Nd0.5)3Ce7Ta2O23.5,二者在1 200℃时的热膨胀系数分别是12.2×10-6,12.5×10-6 K-1,均大于7YSZ的9×10-6 K-1;2种氧化物的热导率和热膨胀系数均满足热障涂层的要求。
标    签 热障涂层   热导率   热膨胀系数   晶体结构   thermal barrier coating   thermal conductivity   thermal expansion coefficient   crystalline structure  
 
Abstract
Taking Sm2O3, NdO3, Dy2O3, Yb2O3, CeO2 and Ta2O5 with high purity as raw materials, (Sm0.5 Nd0.5)3Ce7Ta2O23.5 and (Yb0.5Dy0.5)3Ce7Ta2O23.5 oxides were synthesized by multi-step solid phase sintering at high temperature, and the crystalline structure, micromorphology and thermophysical properties were investigated. The results show that obtained oxides exhibited single fluorite structure. The microstructure was dense, and the interfaces among grains were very clean. The element composition and the atom ratio were consistent with the chemical formula. The thermal conductivity of the two oxides was obviously lower than that of 7YSZ, and the thermal conductivity of (Yb0.5Dy0.5)3Ce7Ta2O23.5 was lower than that of (Sm0.5Nd0.5)3Ce7Ta2O23.5. The thermal expansion coefficient above 900℃ of (Yb0.5Dy0.5)3Ce7Ta2O23.5 was slightly higher than that of (Sm0.5Nd0.5)3Ce7Ta2O23.5, and thermal expansion coefficients at 1 200℃ of two oxides were 12.2×10-6,12.5×10-6 K-1,respectively, which were much higher than 9×10-6 K-1 of 7YSZ. The thermal conductivity and expansion coefficient of the two oxides satisfied the requirements for thermal barrier coatings.

中图分类号 TG174.442   DOI 10.11973/jxgccl202206004

 
  中国光学期刊网论文下载说明


所属栏目 试验研究

基金项目 重庆市教科委科学技术研究项目(KJZD-K201903801)

收稿日期 2021/2/1

修改稿日期 2022/3/14

网络出版日期

作者单位点击查看

备注冉书明(1976-),男,重庆人,副教授,硕士

引用该论文: RAN Shuming,GUO Yi. Thermophysical Performances of (Sm0.5Nd0.5)3Ce7Ta2O23.5 and(Yb0.5Dy0.5)3Ce7Ta2O23.5 Oxides[J]. Materials for mechancial engineering, 2022, 46(6): 21~25
冉书明,郭怡. (Sm0.5Nd0.5)3Ce7Ta2O23.5和(Yb0.5Dy0.5)3Ce7Ta2O23.5氧化物的热物理性能[J]. 机械工程材料, 2022, 46(6): 21~25


论文评价
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
分享论文
分享到新浪微博 分享到腾讯微博 分享到人人网 分享到 Google Reader 分享到百度搜藏分享到Twitter

参考文献
【1】周飞飞,刘敏,邓春明,等.等离子喷涂超高温热障涂层用纳米结构La2(Zr0.75Ce0.25)2O7球形喂料的研究[J].表面技术,2020,49(4):98-103,112. ZHOU F F,LIU M,DENG C M,et al.Nanostructured La2(Zr0.75Ce0.25)2O7 spherical feedstocks for plasma sprayed ultra-high temperature thermal barrier coatings[J].Surface Technology,2020,49(4):98-103,112.
 
【2】李荣久,邓畅光,胡永俊,等.等离子喷涂-物理气相沉积热障涂层的表征技术研究进展[J].表面技术,2020,49(11):124-140. LI R J,DENG C G,HU Y J,et al.Research progress on characterization methods of thermal barrier coatings prepared by plasma spraying-physical vapor deposition[J].Surface Technology,2020,49(11):124-140.
 
【3】刘光,张啸寒,贾利,等.等离子喷涂Mo/8YSZ功能梯度热障涂层结构优化与热力耦合模拟计算[J].表面技术,2020,49(3):213-223. LIU G,ZHANG X H,JIA L,et al.Structural optimization and thermo-mechanical coupling simulation of plasma sprayed Mo/8YSZ functionally graded thermal barrier coating[J].Surface Technology,2020,49(3):213-223.
 
【4】魏晓东,侯国梁,赵荻,等.氧化物掺杂YSZ热障涂层的最新研究进展[J].表面技术,2020,49(6):92-103. WEI X D,HOU G L,ZHAO D,et al.Recent research progress on oxide doped YSZ thermal barrier coatings[J].Surface Technology,2020,49(6):92-103.
 
【5】LOGANATHAN A,GANDHI A S.Effect of phase transformations on the fracture toughness of t'yttria stabilized zirconia[J].Materials Science and Engineering:A,2012,556:927-935.
 
【6】周益春,杨丽,刘志远,等.涡轮叶片热障涂层隔热效果的研究进展[J].中国材料进展,2020,39(10):707-722. ZHOU Y C,YANG L,LIU Z Y,et al.Research progress on insulation performance of thermal barrier coatings on turbine blade[J].Materials China,2020,39(10):707-722.
 
【7】吴硕,赵远涛,李文戈,等.氧化锆基双陶瓷层热障涂层表层材料研究进展[J].表面技术,2020,49(9):101-108. WU S,ZHAO Y T,LI W G,et al.Research progress on top coating materials of thermal barrier coatings with double-ceramic-layer based on zirconia[J].Surface Technology,2020,49(9):101-108.
 
【8】HUANG J B,WANG W Z,LI Y J,et al.Novel-structured plasma-sprayed thermal barrier coatings with low thermal conductivity,high sintering resistance and high durability[J].Ceramics International,2021,47(4):5156-5167.
 
【9】UCZAK DE GOES W,MARKOCSAN N,GUPTA M,et al.Thermal barrier coatings with novel architectures for diesel engine applications[J].Surface and Coatings Technology,2020,396:125950.
 
【10】ZHANG H,SUN J B,DUO S W,et al.Thermal and mechanical properties of Ta2O5 doped La2Ce2O7 thermal barrier coatings prepared by atmospheric plasma spraying[J].Journal of the European Ceramic Society,2019,39(7):2379-2388.
 
【11】LIU K,TANG J J,BAI Y,et al.Particle in-flight behavior and its influence on the microstructure and mechanical property of plasma sprayed La2Ce2O7 thermal barrier coatings[J].Materials Science and Engineering:A,2015,625:177-185.
 
【12】CHEN X G,LU K,ZHAO L M,et al.Thermophysical properties of Ca3Ln3Ce7Ta2O26.5(Ln=Gd and Yb) oxides for thermal barrier coating applications[J].Ceramics International,2020,46(9):14273-14277.
 
【13】CHEN X G,YANG S S,SONG Y,et al.Phase-structures,thermophysical properties of Sm3Ce7Ta2O23.5 and Gd3Ce7Ta2O23.5 oxides for thermal barrier coating applications[J].Ceramics International,2020,46(6):8238-8243.
 
【14】CHEN X G,ZHANG H S,TONG Y P,et al.Thermophysical properties of Ln3Ce7Ta2O23.5 (Ln=Nd and La) composite oxides[J].Ceramics International,2020,46(7):8903-8909.
 
【15】CLARKE D R.Materials selection guidelines for low thermal conductivity thermal barrier coatings[J].Surface and Coatings Technology,2003,163/164:67-74.
 
【16】奚同庚.无机材料热物性学[M].上海:上海科学技术出版社,1981:15-30. XI T G.Thermal physical properties of inorganic materials[M].Shanghai:Shanghai Scientific&Technical Publishers,1981:15-30.
 
【17】PADTURE N P,KLEMENS P G.Low thermal conductivity in garnets[J].Journal of the American Ceramic Society,1997,80(4):1018-1020.
 
相关信息
   标题 相关频次
 热障涂层用新型复合氧化物的制备及其热物理性能
 8
 双相高熵陶瓷(La0.2Eu0.2Gd0.2Y0.2Yb0.2)2Zr2O7的制备与热物理性能
 4
 真空压力浸渗法制备金刚石/铝复合材料及其热性能
 4
 KI体系下制备纯银镀层和纯银/银石墨复合镀层的性能
 2
 NiCoCrAlY-ZrO2·Y2O3涂层在1100℃不同时间的氧化行为
 2
 SiO2微粉加入量对焦宝石基喷涂耐火材料抗热震性能的影响
 2
 玻璃含量对低温烧结硼硅酸盐玻璃-AlN陶瓷复合材料性能的影响
 2
 不同含量Al2O3微粒改性环氧树脂复合材料的导热和导电特性
 2
 磁控溅射法制备ZrW2O8薄膜及其性能
 2
 导电薄膜热膨胀系数实时测试系统
 2
 导体材料涡流热成像应力检测的仿真
 2
 等离子喷涂8YSZ热障涂层隔热效果及内应力演变有限元模拟
 2
 等离子喷涂纳米结构ZrO2-7%Y2O3热障涂层的组织及性能
 2
 等离子喷涂热障涂层中应力分布的有限元模拟
 2
 等离子喷涂物理气相沉积(PS-PVD)热障涂层在高温高速航空煤油燃气热冲击下的失效机制
 2
 等离子喷涂制备Al2O3/ZrO2复合结构热障涂层的性能
 2
 电阻瞬态法测定材料的传热性能
 2
 顶杆法热膨胀系数测试在材料性能研究中的应用
 2
 反应烧结制备AlON-AlN复相陶瓷及其性能
 2
 氟碳封孔剂封孔处理对8YSZ热障涂层电化学腐蚀及抗盐雾腐蚀性能的影响
 2
 高导热碳化硅陶瓷的研究进展
 2
 基于超声特征成像技术的铝硅热障涂层脱粘缺陷检测
 2
 晶化温度对Li2O-ZnO-Al2O3-SiO2微晶玻璃物相组成和热膨胀系数的影响
 2
 热处理参数对锂锌硅系微晶玻璃中方石英相含量的影响
 2
 热导性电绝缘界面材料热传输特性参数的测量
 2
 热障涂层制备技术研究进展
 2
 烧结助剂La2O3含量对热压烧结制备Si3N4-AlN复相陶瓷性能的影响
 2
 水基干压成型高导热氮化硅陶瓷的结构和性能
 2
 陶瓷层孔隙对热障涂层TGO界面残余应力影响的有限元研究
 2
 梯度SiCP/Al复合材料的组织与性能
 2