Industrial CT measurement method of the wave-shaped oil chamber position in piston
摘 要
内冷油道是活塞内部起冷却作用的重要结构,其位置对活塞各个部位的工作温度有重要影响。使用传统圆环形油道位置的测量方法检测波浪形内冷油道时,存在线阵工业CT方法不适用的问题,为此研究了波浪形内冷油道位置的工业CT测量方法。该方法基于DR和线阵工业CT技术,通过合理设置扫描位置,确定最少的切片数量,实现了活塞波浪形内冷油道位置的测量。最后采用三坐标测量机对该方法进行验证,结果表明,其测量误差在5%以内,与其他方法相比,该方法检测成本更低,检测效率更高。
Abstract
The oil chamber is an important structure for cooling inside the piston, and its position has an important impact on the working temperature of all parts of the piston. For the measurement of the wave-shaped oil chamber position, some difficulties may exist, such as that the linear array industrial CT is not applicable and the ultrasonic detection can not be performed. The industrial CT method for the position measurement of the wave-shaped oil chamber is studied. It is based on the DR and linear array industrial CT to set the setting of scanning position and determine the minimum number of sections. The method is verified, which shows that the measurement error is within 5%. The method has lower detection cost and higher detection efficiency.
中图分类号 TG115.28 DOI 10.11973/wsjc202208006
所属栏目 试验研究
基金项目
收稿日期 2021/11/30
修改稿日期
网络出版日期
作者单位点击查看
备注徐凤丽(1996-),女,硕士研究生,主要研究方向为工业CT
引用该论文: XU Fengli,NI Peijun,QI Zicheng,ZHANG Weiguo,FU Kang. Industrial CT measurement method of the wave-shaped oil chamber position in piston[J]. Nondestructive Testing, 2022, 44(8): 31~35
徐凤丽,倪培君,齐子诚,张维国,付康. 活塞波浪形内冷油道位置的工业CT测量[J]. 无损检测, 2022, 44(8): 31~35
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】宗明景, 董非, 朱楠林. 内冷油道位置对柴油机活塞温度场的影响研究[J].机电工程, 2017, 34(12): 1422-1426.
【2】潘铭. 船用柴油机活塞制造主要工艺分析[J].产业与科技论坛, 2014, 13(21): 46-47.
【3】林名升. 铝活塞毛坯的制造[J]. 金属加工, 2009(19): 65-67.
【4】林旭, 陈国玉, 李源, 等. 基于APDL语言的活塞热应力分析[J]. 天津理工大学学报,2019,35(4):14-18.
【5】吕彩琴, 苏铁熊. 活塞冷却油腔位置对活塞强度的影响[J]. 内燃机, 2009(1): 4-9.
【6】王浩, 张龙, 黄贞益. 汽车活塞浇注系统的改进及数值模拟[J]. 铸造, 2019, 68(1): 34-37.
【7】MEI H S,XIAO Y,LI R Q,et al.Failure analysis of the casting aluminum pistons of internal combustion engines[J]. Journal of Netshape Forming Engineering, 2013, 5(4): 60-63.
【8】盛伟, 谭勇敢, 雷曦. 大缸径柴油机铸铝镶圈活塞制造工艺[J]. 机车车辆工艺, 2015, 2(1): 1-4.
【9】盖少磊. 大功率柴油机活塞设计与制造技术[J]. 现代制造技术与装备, 2013, 5: 26-27.
【10】孙晓, 王艳艳, 王磊, 等. 铝合金活塞制造工艺现状及发展方向[J]. 内燃机与配件, 2010, 5: 26-28.
【11】SU P, CHEN Y T, CHEN D P, et al. Numerical Simulation Study of Casting Process for Aluminum Alloy Piston of Diesel Engine[J]. Journal of Netshape Forming Engineering, 2016(2): 59-63, 67.
【12】陆英豪, 倪培君, 齐子诚, 等. 活塞燃烧室的涡流阵列检测[J]. 无损检测, 2021, 43(4): 30-35.
【13】齐子诚, 张国斌, 唐盛明, 等. 活塞镶圈结合面质量的快速无损检测系统[J]. 无损检测, 2015,37(8):71-75.
【14】倪培君. 大马力发动机活塞无损检测研究现状与进展[J]. 无损检测, 2011, 33(9): 7-10,15.
【15】郝丽萍, 齐子诚, 郑颖, 等.活塞内冷油腔CT图像自动测量方法及实现[J]. 无损检测, 2013, 35(8): 39-43.
【16】付汝龙, 姚子龙, 曾庆勋. 活塞内冷油道缺陷相控阵超声检测[J]. 无损探伤, 2016, 40(2): 41-42.
【17】齐子诚, 倪培君, 姜伟, 等. 金属材料内部缺陷精确工业CT测量方法[J]. 强激光与粒子束, 2018, 30(2): 025102.
【18】DE C L, CARMIGNATO S, KRUTH J P. Industrial applications of computed tomography[J]. CIRP Annals-Manufacturing Technology, 2014, 63: 655-677.
【19】付康, 倪培君, 唐盛明, 等. 基于工业CT线性尺寸测量的不确定度分析[J]. 强激光与粒子束, 2018, 30(5): 055103.
【2】潘铭. 船用柴油机活塞制造主要工艺分析[J].产业与科技论坛, 2014, 13(21): 46-47.
【3】林名升. 铝活塞毛坯的制造[J]. 金属加工, 2009(19): 65-67.
【4】林旭, 陈国玉, 李源, 等. 基于APDL语言的活塞热应力分析[J]. 天津理工大学学报,2019,35(4):14-18.
【5】吕彩琴, 苏铁熊. 活塞冷却油腔位置对活塞强度的影响[J]. 内燃机, 2009(1): 4-9.
【6】王浩, 张龙, 黄贞益. 汽车活塞浇注系统的改进及数值模拟[J]. 铸造, 2019, 68(1): 34-37.
【7】MEI H S,XIAO Y,LI R Q,et al.Failure analysis of the casting aluminum pistons of internal combustion engines[J]. Journal of Netshape Forming Engineering, 2013, 5(4): 60-63.
【8】盛伟, 谭勇敢, 雷曦. 大缸径柴油机铸铝镶圈活塞制造工艺[J]. 机车车辆工艺, 2015, 2(1): 1-4.
【9】盖少磊. 大功率柴油机活塞设计与制造技术[J]. 现代制造技术与装备, 2013, 5: 26-27.
【10】孙晓, 王艳艳, 王磊, 等. 铝合金活塞制造工艺现状及发展方向[J]. 内燃机与配件, 2010, 5: 26-28.
【11】SU P, CHEN Y T, CHEN D P, et al. Numerical Simulation Study of Casting Process for Aluminum Alloy Piston of Diesel Engine[J]. Journal of Netshape Forming Engineering, 2016(2): 59-63, 67.
【12】陆英豪, 倪培君, 齐子诚, 等. 活塞燃烧室的涡流阵列检测[J]. 无损检测, 2021, 43(4): 30-35.
【13】齐子诚, 张国斌, 唐盛明, 等. 活塞镶圈结合面质量的快速无损检测系统[J]. 无损检测, 2015,37(8):71-75.
【14】倪培君. 大马力发动机活塞无损检测研究现状与进展[J]. 无损检测, 2011, 33(9): 7-10,15.
【15】郝丽萍, 齐子诚, 郑颖, 等.活塞内冷油腔CT图像自动测量方法及实现[J]. 无损检测, 2013, 35(8): 39-43.
【16】付汝龙, 姚子龙, 曾庆勋. 活塞内冷油道缺陷相控阵超声检测[J]. 无损探伤, 2016, 40(2): 41-42.
【17】齐子诚, 倪培君, 姜伟, 等. 金属材料内部缺陷精确工业CT测量方法[J]. 强激光与粒子束, 2018, 30(2): 025102.
【18】DE C L, CARMIGNATO S, KRUTH J P. Industrial applications of computed tomography[J]. CIRP Annals-Manufacturing Technology, 2014, 63: 655-677.
【19】付康, 倪培君, 唐盛明, 等. 基于工业CT线性尺寸测量的不确定度分析[J]. 强激光与粒子束, 2018, 30(5): 055103.
相关信息