Influence of Heat Treatment Process on Microstructure and Tensile Property of Ti55531 Titanium Alloy
摘 要
利用光学显微镜、扫描电子显微镜和拉伸试验机等设备, 研究了热处理工艺对Ti55531钛合金显微组织和拉伸性能的影响。结果表明: 随着固溶温度的升高(790~810 ℃), 合金中初生α相(αp)的含量减少, 合金强度升高而塑性降低; 随着时效温度的升高(500~600 ℃), 合金中次生α相(αs)变粗变长, 合金强度降低而塑性升高; 随着550 ℃时效时间的延长(2~8 h), 合金中析出的αs相含量增多, 强度升高, 塑性有所降低。
Abstract
By means of optical microscopy (OM), scanning electron microscopy (SEM) and tensile testing machine the influences of heat treatment process on microstructure and tensile property of Ti55531 titanium alloy were studied. The results show that with the increase of solid solution temperature (790-810 ℃), the content of primary α phase in the alloy decreased, the strength increased and the plasticity decreased. With the increase of aging temperature (500-600 ℃), the secondary α phase in the alloy coarsened, the strength of alloy decreased and plasticity increased. When the prolongation of aging time (2-8 h) at 550 ℃, the content of secondary α phase in the alloy increased, the strength of the alloy increased and the plasticity decreased.
中图分类号 TG156.1
所属栏目 试验研究
基金项目 国家重点基础研究发展计划资助项目(2010CB630805)
收稿日期 2013/6/14
修改稿日期 2014/6/22
网络出版日期
作者单位点击查看
备注黄剑锋(1987-), 男, 福建南平人, 硕士研究生。
引用该论文: HUANG Jian-feng,YONG Qi-long,SUN Xin-jun,LI Zhao-dong. Influence of Heat Treatment Process on Microstructure and Tensile Property of Ti55531 Titanium Alloy[J]. Materials for mechancial engineering, 2014, 38(8): 20~23
黄剑锋,雍岐龙,孙新军,李昭东. 热处理工艺对Ti55531钛合金显微组织与拉伸性能的影响[J]. 机械工程材料, 2014, 38(8): 20~23
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】付艳艳, 宋月清, 惠松晓, 等. 航空用钛合金的研究与应用进展[J].稀有金属,2006,30(6): 850-856.
【2】李启鹏, 李伟.航空用钛合金抗微动疲劳表面改性技术的研究进展[J].机械工程材料, 2012, 36(11): 9-13.
【3】葛鹏, 赵永庆, 周廉.一种新型高强亚稳β钛合金Ti-B20[J].稀有金属材料与工程,2005,34(5): 790-794.
【4】周伟, 葛鹏, 赵永庆, 等.一种近β型钛合金的热处理响应[J].稀有金属材料与工程,2010,39(4): 723-726.
【5】韩栋,张鹏省,毛小南, 等.两种典型热处理工艺对TC18钛合金组织性能的影响[J].钛工业进展,2009,26(6): 365-369.
【6】官杰,刘建荣, 雷家峰.TC18钛合金的组织和性能与热处理制度的关系[J].材料研究学报,2009,23(1): 77-82.
【7】JONES N G, DASHWOOD R J,DYE D, et al. Thermo mechanical processing of Ti-5Al-5Mo-5V-3Cr[J].Materials Science and Engineering: A,2008,490: 369-376.
【8】高玉社,李少强,张钢, 等.热处理工艺对Ti55531钛合金组织及性能的影响[J].西安工业大学学报,2011,31(4): 365-369.
【9】FANNING J C,BOYER R R.Ti-2003 science and technology[M].[S.l.]: Wiley VCH,2004: 2643.
【10】徐锋,计波,朱义藩,等.加工工艺对Ti5553合金等温锻件力学性能和显微组织的影响[J].中国有色金属学报,2010,20(1): 100-103.
【11】贾百芳.热处理对 TC18 钛合金显微组织参数及力学性能的影响[D].西安: 西安建筑科技大学, 2011: 8-10.
【12】付艳艳,宋月清,惠松骁,等.热处理对VST55531钛合金的组织和拉伸性能的影响[J].稀有金属, 2008, 32(4): 399-403.
【13】周义刚, 张宝昌.钛合金近β锻造研究 [J].航空学报, 1989, 10(1): 60-66.
【14】ONODERA H, ABE T, NAKAZAWA S, et al. Creep properties of α+α2 type Ti-Al-Sn-Zr-Nb-Si alloys designed with the aid of thermodynamics[J].ISIJ International, 1993, 33(7): 793-798.
【2】李启鹏, 李伟.航空用钛合金抗微动疲劳表面改性技术的研究进展[J].机械工程材料, 2012, 36(11): 9-13.
【3】葛鹏, 赵永庆, 周廉.一种新型高强亚稳β钛合金Ti-B20[J].稀有金属材料与工程,2005,34(5): 790-794.
【4】周伟, 葛鹏, 赵永庆, 等.一种近β型钛合金的热处理响应[J].稀有金属材料与工程,2010,39(4): 723-726.
【5】韩栋,张鹏省,毛小南, 等.两种典型热处理工艺对TC18钛合金组织性能的影响[J].钛工业进展,2009,26(6): 365-369.
【6】官杰,刘建荣, 雷家峰.TC18钛合金的组织和性能与热处理制度的关系[J].材料研究学报,2009,23(1): 77-82.
【7】JONES N G, DASHWOOD R J,DYE D, et al. Thermo mechanical processing of Ti-5Al-5Mo-5V-3Cr[J].Materials Science and Engineering: A,2008,490: 369-376.
【8】高玉社,李少强,张钢, 等.热处理工艺对Ti55531钛合金组织及性能的影响[J].西安工业大学学报,2011,31(4): 365-369.
【9】FANNING J C,BOYER R R.Ti-2003 science and technology[M].[S.l.]: Wiley VCH,2004: 2643.
【10】徐锋,计波,朱义藩,等.加工工艺对Ti5553合金等温锻件力学性能和显微组织的影响[J].中国有色金属学报,2010,20(1): 100-103.
【11】贾百芳.热处理对 TC18 钛合金显微组织参数及力学性能的影响[D].西安: 西安建筑科技大学, 2011: 8-10.
【12】付艳艳,宋月清,惠松骁,等.热处理对VST55531钛合金的组织和拉伸性能的影响[J].稀有金属, 2008, 32(4): 399-403.
【13】周义刚, 张宝昌.钛合金近β锻造研究 [J].航空学报, 1989, 10(1): 60-66.
【14】ONODERA H, ABE T, NAKAZAWA S, et al. Creep properties of α+α2 type Ti-Al-Sn-Zr-Nb-Si alloys designed with the aid of thermodynamics[J].ISIJ International, 1993, 33(7): 793-798.
相关信息