Discussion on Stress Corrosion of Stainless Steels from Failure Cases
摘 要
对三种不同牌号不锈钢构件的应力腐蚀失效案例进行了分析, 讨论了影响不锈钢实际使用效果的常见因素。分析认为, 在不锈钢材料和构件的制造和使用过程中, 要严格控制冷热加工的变形率和温度, 并避免材料长期在敏化温度下工作; 要充分了解各类不锈钢的材料特性以及构件的使用环境, 特别是要考虑某些极端条件对材料耐蚀性的影响, 才能更加合理地选择不锈钢; 在设计不锈钢构件时, 要充分考虑强度对不锈钢耐蚀性的影响, 尽量降低其工艺强度水平, 不宜采用材料强度上限设计, 如果在此情况下强度不能满足要求, 应选用更高强度的其它材料。
Abstract
By analyzing stress corrosion failure cases of three kinds of stainless steel, the factors affecting the practical effect of stainless steels were discussed. The results show that it is necessary to control the hot and cold deformation rate and temperature strictly during processing, and to avoid long-term using under sensitization temperature condition. By understanding material characteristics and using environment of stainless steels, especially the influence of extreme conditions on the corrosion resistance of materials, it is able to choose stainless steels more reasonably. It is necessary to consider the impact of strength on corrosion resistance of stainless steels, and to reduce the level of technology intensity as much as possible. It is inadvisable to employ the maximum design strength of materials. If strength can not meet the requirements, It is advisable to choosey material which has higher intensity.
中图分类号 TG172.9
所属栏目 应用技术
基金项目
收稿日期 2010/6/13
修改稿日期 2010/7/6
网络出版日期
作者单位点击查看
联系人作者姜涛(tibu98@sina.com)
备注姜涛, 工程师,
引用该论文: JIANG Tao,YU Yang,YANG Sheng,MA Hai-quan,BAI Ming-yuan,CHEN Xing. Discussion on Stress Corrosion of Stainless Steels from Failure Cases[J]. Corrosion & Protection, 2011, 32(4): 297
被引情况:
【1】刘德林,李春光,陶春虎,何玉怀,李莹, "铍青铜弹簧片应力腐蚀开裂分析",腐蚀与防护 33, 452-455(2012)
【2】秦承鹏,李梁, "600 MW超临界机组低压转子叶片开裂分析",腐蚀与防护 37, 936-938(2016)
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】朱相荣, 王相润. 金属材料的海洋腐蚀与防护[M]. 北京:国防工业出版社, 1999.
【2】陈颖锋. 催化气压机出口冷却器换热管开裂原因分析[J]. 压力容器, 2002, 19(9):44-46.
【3】李正刚, 杨厚君, 李朝志. 锅炉再热管腐蚀失效及防止措施[J]. 材料保护, 2003, 36(6):35-37.
【4】史冬梅, 李金许, 高克玮, 等. 小锥度试样在研究应力腐蚀裂纹形核中的应用[J]. 北京科技大学学报, 2008, 30(5):501-505.
【5】陆永浩, 褚武扬, 高克玮, 等. 304L不锈钢在高温水中的应力腐蚀裂纹扩展[J]. 金属学报, 2004, 40(7):763-767.
【6】赵东, 李京民, 马彦东, 等. 316L不锈钢波纹管泄漏原因分析[J]. 失效分析与预防, 2009, 4(4):217-221.
【2】陈颖锋. 催化气压机出口冷却器换热管开裂原因分析[J]. 压力容器, 2002, 19(9):44-46.
【3】李正刚, 杨厚君, 李朝志. 锅炉再热管腐蚀失效及防止措施[J]. 材料保护, 2003, 36(6):35-37.
【4】史冬梅, 李金许, 高克玮, 等. 小锥度试样在研究应力腐蚀裂纹形核中的应用[J]. 北京科技大学学报, 2008, 30(5):501-505.
【5】陆永浩, 褚武扬, 高克玮, 等. 304L不锈钢在高温水中的应力腐蚀裂纹扩展[J]. 金属学报, 2004, 40(7):763-767.
【6】赵东, 李京民, 马彦东, 等. 316L不锈钢波纹管泄漏原因分析[J]. 失效分析与预防, 2009, 4(4):217-221.
相关信息