Effects of Heat Treatment Process on Morphology and Properties of Foam Iron
摘 要
首先在聚氨酯泡沫基体表面化学镀一层铜, 然后电沉积铁, 再对聚氨酯进行不同方式的热解, 最后对泡沫铁进行还原热处理, 研究了热处理工艺对泡沫铁结构与性能的影响, 以及热解方式对泡沫铁性能的影响。结果表明:在氮气中热解聚氨酯基体可以有效减少泡沫铁的氧化, 获得更好的力学性能; 在相变温度以上进行热处理可以有效消除泡沫铁的脆性, 减少缺陷; 在960 ℃左右的还原气氛中保温处理2 h, 可使泡沫铁获得较好的力学性能。
Abstract
A layer of copper was coated on polyurethane foam substrate surface by chemical plating first, and iron electro-deposition was followed, then the polyurethane was pyrolysed, and finally, the foam iron was heated under a reduced atmosphere. The effect of heat treatment on the structure and properties of foamed iron and the effect of pyrolysis on properties of the foam iron were studied. The results show that the mechanical properties of the foam iron could be enhanced when the polyurethane was pyrolysed in nitrogen atmosphere. It could effectively make foam iron eliminating brittleness and reducing defects when the heat treatment was performed above phase-transition temperature; and fairly good mechanical properties could be obtained after the foam iron was treated at 960 ℃ for 2 h in reducing atmosphere.
中图分类号 TG156.1
所属栏目 新材料 新工艺
基金项目 国家自然科学基金重大研究计划项目(90916021)
收稿日期 2011/10/23
修改稿日期 2011/12/1
网络出版日期
作者单位点击查看
备注单伟根(1984-), 男, 山东威海人, 硕士研究生。
引用该论文: SHAN Wei-gen,LI Yang,XU Chen,LU Min,GUO Dong-jie,DAI Zhen-dong. Effects of Heat Treatment Process on Morphology and Properties of Foam Iron[J]. Materials for mechancial engineering, 2012, 36(11): 58~61
单伟根,李阳,徐晨,卢敏,郭东杰,戴振东. 热处理工艺对泡沫铁结构与性能的影响[J]. 机械工程材料, 2012, 36(11): 58~61
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】RABIEI A, VENDRA L J. A comparison of composite metal foam′s properties and other comparable metal foams[J]. Materials Letters, 2009, 63:533-536.
【2】BROTHER A. DUNAND D C. Amorphous metal foams[J]. Scripta Materialia, 2006, 54(4):513-520.
【3】BANHART J. Manufacture, characterization and application of cellular metals and metal foams[J]. Progress in Materials Science, 2001, 46:559-632.
【4】BADICHE X, FOREST S, GUIBERT T. Mechanical properties and non-homogeneous deformation of open-cell nickel foams:application of the mechanics of cellular solids and of porous materials[J]. Materials Science and Engineering A, 2000, 289(1/2):276-288.
【5】张芳, 王录才. 泡沫金属的研究与发展[J]. 铸造设备研究, 2000(3):38-51.
【6】陈文革. 泡沫金属的特点、应用、制备与发展[M]. 北京:粉末冶金工业出版社, 2005:37-42.
【7】左正忠, 梁国柱, 李卫东, 等. 全光亮镀铁工艺的研究[J]. 武汉大学学报:理学版, 2001, 47(6) :679-702.
【8】BANHART J. Preparation and characterization of high-porosity titanium, stainless steel and superalloy parts[J]. Metal Foams and Porous Structures, 1999:197-202
【9】赵鹏, 浦玉萍, 黄春晖, 等. 超声波对聚氨酯泡沫塑料化学镀铜的影响[J]. 材料工程, 2008(4):43-46.
【10】吴伟. 泡沫铁材料的制备及其性能的研究[D]. 秦皇岛: 燕山大学, 2010.
【11】孙路阳, 侯广亚, 曹华珍, 等. 电化学沉积法制备泡沫铁及其性能研究[J]. 浙江工业大学学报, 2010, 38(5): 508-513.
【12】陈红辉, 朱爱平, 夏健康, 等. 泡沫铁制备工艺的研究[J]. 电镀与环保, 2007, 9(5):11-12.
【13】陈红辉, 郝胜策, 高原, 等. 超声波对泡沫铁结构的影响[J]. 电镀与环保, 2009, 29(3):15-17.
【14】徐临超. 电流波形对铁电镀层结构和性能的影响[J]. 电镀与涂饰, 2010, 29(9):5-8.
【15】宫凯, 黄因慧, 田宗军, 等. 喷射电沉积制备多孔金属镍工艺[J]. 机械工程材料, 2008, 32(8):40-46.
【16】刘仁志. 实用电镀技术[M]. 北京:化学工业出版社, 2006:47-88.
【17】陈范才, 肖鑫, 周琦, 等. 现代电镀技术[M].北京: 中国纺织出版社, 2009.
【18】戴永年. 二元合金相图[M]. 北京:科学出版社, 2009:242.
【2】BROTHER A. DUNAND D C. Amorphous metal foams[J]. Scripta Materialia, 2006, 54(4):513-520.
【3】BANHART J. Manufacture, characterization and application of cellular metals and metal foams[J]. Progress in Materials Science, 2001, 46:559-632.
【4】BADICHE X, FOREST S, GUIBERT T. Mechanical properties and non-homogeneous deformation of open-cell nickel foams:application of the mechanics of cellular solids and of porous materials[J]. Materials Science and Engineering A, 2000, 289(1/2):276-288.
【5】张芳, 王录才. 泡沫金属的研究与发展[J]. 铸造设备研究, 2000(3):38-51.
【6】陈文革. 泡沫金属的特点、应用、制备与发展[M]. 北京:粉末冶金工业出版社, 2005:37-42.
【7】左正忠, 梁国柱, 李卫东, 等. 全光亮镀铁工艺的研究[J]. 武汉大学学报:理学版, 2001, 47(6) :679-702.
【8】BANHART J. Preparation and characterization of high-porosity titanium, stainless steel and superalloy parts[J]. Metal Foams and Porous Structures, 1999:197-202
【9】赵鹏, 浦玉萍, 黄春晖, 等. 超声波对聚氨酯泡沫塑料化学镀铜的影响[J]. 材料工程, 2008(4):43-46.
【10】吴伟. 泡沫铁材料的制备及其性能的研究[D]. 秦皇岛: 燕山大学, 2010.
【11】孙路阳, 侯广亚, 曹华珍, 等. 电化学沉积法制备泡沫铁及其性能研究[J]. 浙江工业大学学报, 2010, 38(5): 508-513.
【12】陈红辉, 朱爱平, 夏健康, 等. 泡沫铁制备工艺的研究[J]. 电镀与环保, 2007, 9(5):11-12.
【13】陈红辉, 郝胜策, 高原, 等. 超声波对泡沫铁结构的影响[J]. 电镀与环保, 2009, 29(3):15-17.
【14】徐临超. 电流波形对铁电镀层结构和性能的影响[J]. 电镀与涂饰, 2010, 29(9):5-8.
【15】宫凯, 黄因慧, 田宗军, 等. 喷射电沉积制备多孔金属镍工艺[J]. 机械工程材料, 2008, 32(8):40-46.
【16】刘仁志. 实用电镀技术[M]. 北京:化学工业出版社, 2006:47-88.
【17】陈范才, 肖鑫, 周琦, 等. 现代电镀技术[M].北京: 中国纺织出版社, 2009.
【18】戴永年. 二元合金相图[M]. 北京:科学出版社, 2009:242.
相关信息