Predicting Mechanical Constitutive Relationship of Polypropylene
摘 要
采用显示动力中心差分计算方法对聚丙烯(PP)材料的力学本构关系进行了参数分析, 通过拉伸试验, 得到了四种拉伸速度(即四种应变速率)下的拉伸试验曲线, 使用Cowper-Symonds模型结合有限元动力学计算的方法分析上述拉伸试验曲线, 得了PP材料的力学本构关系参数。结果表明: 用上述方法可以准确预测PP材料的力学本构关系参数, 应变速率参数C和P分别为179.25和2.6; 并给出了PP材料在静拉伸状态下的弹性模量、屈服值和应力-有效塑性应变曲线拟合公式。
Abstract
Explicit central difference method for dynamics was applied to parametric analysis on the mechanical constitutive relationship of automotive polypropylene (PP) material. The tensile testing was carried out to obtain the tensile curves at four strain rates. The method of combining Cowper-Symonds model and finite element dynamic caculation was used to analyze the above curves, and then mechanical costitutive relationship parameters of PP material were obtained. The results show that the method could predict mechanical costitutive relationship parameters of PP material accurately, the strain rate parameters C and P were 179.25 and 4.6, respectively. The elastic modulus, yield value and fitting formula of stress-effective plastic strain curves for PP material in static tension were obtained, constitutive relationship parameters based on Cowper-Symonds model were obtained.
中图分类号 TH145.4
所属栏目 物理模拟与数值模拟
基金项目 创新研究群体科学基金资助项目(50921001); 国家重点基础研究发展计划项目(2010CB832700)
收稿日期 2011/12/1
修改稿日期 2012/9/19
网络出版日期
作者单位点击查看
备注董晓磊(1986-)男, 山东莱阳人, 硕士研究生。
引用该论文: DONG Xiao-lei,ZONG Zhi,LI Lei,WANG Xi-jun,NIE Chun. Predicting Mechanical Constitutive Relationship of Polypropylene[J]. Materials for mechancial engineering, 2013, 37(2): 95~99
董晓磊,宗智,李磊,王喜军,聂春. 聚丙烯材料力学本构关系的预测[J]. 机械工程材料, 2013, 37(2): 95~99
被引情况:
【1】曹新鑫,霍国洋,王优,孙晓晴,王慧元,孙得翔, "不同配比粉煤灰/聚丙烯复合材料的性能",机械工程材料 38, 35-38(2014)
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】冯美斌.汽车轻量化技术中新材料的发展及应用[J].汽车工程, 2006, 28(2): 213-220.
【2】吴三清.汽车用改性聚丙烯(PP)材料的开发与应用[J].汽车工艺与材料, 2004, 16(2): 26-28.
【3】徐涛, 于杰, 雷华, 等.聚丙烯材料聚集态结构的定量表征及其与力学性能的关系[J].高分子学报, 2001, 2(4): 147-152.
【4】于润泽, 刘正英, 尹波, 等.纳米粒子的分散状态对聚丙烯结晶行为的影响[J].高分子材料科学与工程, 2006, 22(5): 147-150.
【5】ZHANG X M, YIN Z H, NA T H, et al.Morphology, mechanical properties and interfacial behavior of PA1010/PP/PP-g-GMA ternary blends [J]. Polymer, 2006, 22(5): 147-150.
【6】李文东, 杨桂生.分子量及其分布对聚丙烯力学性能和结晶行为的影响[J].高分子材料科学与工程, 1996, 4(1): 41-45.
【7】姜云鹏, 岳珠峰, 韩小平.由拉伸试样确定材料真实应力应变关系[J].机械工程, 2003, 25(2): 151-153.
【8】尚晓江, 苏建宁.ANSYS/LS-DYNA动力分析方法与工程实例[M].北京: 中国水利水电出版社, 2005.
【9】CHOUNG J, CHO S R, KIM K S.Impact test simulations of stiffened plates using the micromechanical porous plasticity model[J].Ocean Engineering, 2010, 37(5): 749-756.
【2】吴三清.汽车用改性聚丙烯(PP)材料的开发与应用[J].汽车工艺与材料, 2004, 16(2): 26-28.
【3】徐涛, 于杰, 雷华, 等.聚丙烯材料聚集态结构的定量表征及其与力学性能的关系[J].高分子学报, 2001, 2(4): 147-152.
【4】于润泽, 刘正英, 尹波, 等.纳米粒子的分散状态对聚丙烯结晶行为的影响[J].高分子材料科学与工程, 2006, 22(5): 147-150.
【5】ZHANG X M, YIN Z H, NA T H, et al.Morphology, mechanical properties and interfacial behavior of PA1010/PP/PP-g-GMA ternary blends [J]. Polymer, 2006, 22(5): 147-150.
【6】李文东, 杨桂生.分子量及其分布对聚丙烯力学性能和结晶行为的影响[J].高分子材料科学与工程, 1996, 4(1): 41-45.
【7】姜云鹏, 岳珠峰, 韩小平.由拉伸试样确定材料真实应力应变关系[J].机械工程, 2003, 25(2): 151-153.
【8】尚晓江, 苏建宁.ANSYS/LS-DYNA动力分析方法与工程实例[M].北京: 中国水利水电出版社, 2005.
【9】CHOUNG J, CHO S R, KIM K S.Impact test simulations of stiffened plates using the micromechanical porous plasticity model[J].Ocean Engineering, 2010, 37(5): 749-756.
相关信息