Defect Analysis and Elimination of ZCuSn10Zn2 Products by Centrifugal Casting
摘 要
某ZCuSn10Zn2离心铸造产品粗加工后, 经超声波探伤发现有疑似夹杂物超标缺陷。通过宏观检验、化学成分分析以及金相检验手段对缺陷性质和产生原因进行了分析。结果表明: 该产品疑似夹杂物缺陷为组织偏析。最后采用热处理手段消除了偏析缺陷, 并使产品的综合力学性能得到显著提升。
Abstract
Defects which was suspected as inclusion were found after rough machining by ultrasonic testing in the ZCuSn10Zn2 centrifugal casting products. The property and reason of the defects were analyzed and judged by means of macroscopic inspection, chemical composition analysis and metallographic examination. The results showed that the property of the defects were structure segregation. The segregation defects were eliminated by heat treatment method, and resulting in the much increase of synthesis mechanical property of the alloy.
中图分类号 TG166.2
所属栏目 质量控制与失效分析
基金项目
收稿日期 2012/4/21
修改稿日期
网络出版日期
作者单位点击查看
备注刘铁山(1957-),男,工程师。
引用该论文: LIU Tie-shan,GUO Ya-sen,SONG Ya-hu,SUN Sheng-wei,ZHOU Wei-xing. Defect Analysis and Elimination of ZCuSn10Zn2 Products by Centrifugal Casting[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2013, 49(1): 52~54
刘铁山,郭亚森,宋亚虎,孙胜伟,周维兴. ZCuSn10Zn2离心浇铸产品缺陷的分析和消除[J]. 理化检验-物理分册, 2013, 49(1): 52~54
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】杨为勤.大型锡青铜艉轴衬套的离心铸造工艺研究[J].铸造, 2010,59(10):1007-1011.
【2】聂小武. 锡青铜的熔炼工艺及铸造缺陷防止[J]. 中国铸造装备与技术,2010(5):24-25.
【3】李文钱,刘航,林国标,等.Zn,Sn对真空铸造锡青铜性能的影响[J]. 热加工工艺, 2008,37(5):37-39.
【4】王贤涛.采用半金属型法生产锡青铜衬套的铸造工艺[J]. Hot Working Technology,2004(11):74.
【5】林国标,王自东,张伟,等.热处理对锡青铜合金组织和性能的影响[J].铸造,2011,60(3):287-293.
【2】聂小武. 锡青铜的熔炼工艺及铸造缺陷防止[J]. 中国铸造装备与技术,2010(5):24-25.
【3】李文钱,刘航,林国标,等.Zn,Sn对真空铸造锡青铜性能的影响[J]. 热加工工艺, 2008,37(5):37-39.
【4】王贤涛.采用半金属型法生产锡青铜衬套的铸造工艺[J]. Hot Working Technology,2004(11):74.
【5】林国标,王自东,张伟,等.热处理对锡青铜合金组织和性能的影响[J].铸造,2011,60(3):287-293.
相关信息