基于声发射检测的碳布/环氧树脂复合材料压缩损伤评价
Compression Damage Evaluation of Carbon-Cloth / Epoxy Composite Based on Acoustic Emission Testing
摘 要
用声发射仪器监测二维编织碳布/环氧树脂复合材料的压缩损伤过程。通过载荷与声发射特征关系图，判断出其在损伤过程中的临界失效载荷，作为判断材料临界损伤强度的依据。通过对碳布/环氧树脂复合材料在压缩损伤过程中产生的声发射信号进行小波包分解，并对信号进行频谱分析以及对小波包分解后的各层进行能量分析，得出了声发射源即纤维断裂信号、基体断裂信号和层间开裂信号的频率分布范围。
复合材料
小波包分析
压缩损伤评价
Acoustic emission testing
Composite material
Wavelet packet analysis
Compression damage evaluation
Abstract
Acoustic emission(AE) system was used to monitor the compression damage of carbon-cloth/epoxy materials. The critical load of failure was acquired from the experimental correlogram of the loads and characters of the acoustic emission signals. Through wavelet packet analysis and spectrum analysis of acoustic emission signals, and energy analysis of every stage acquired from wavelet packet analysis in the compression damage evolution of carbon-cloth/epoxy materials, the frequency range of the acoustic emission sources of the fiber breakage, matrix fracture and delamination breakage signals were acquired.
中图分类号 TG115.28
所属栏目 试验研究
基金项目 国家自然科学基金资助项目(10964008)
收稿日期 2010/12/28
修改稿日期
网络出版日期
作者单位点击查看
备注丁鹏(1986-)，男，硕士研究生，研究方向为声发射无损检测。
引用该论文: DING Peng,LU Chao,CHEN Zhen-Hua,XIE Xiao-Lin. Compression Damage Evaluation of Carbon-Cloth / Epoxy Composite Based on Acoustic Emission Testing[J]. Nondestructive Testing, 2011, 33(11): 29～32
丁鹏,卢超,陈振华,谢小林. 基于声发射检测的碳布/环氧树脂复合材料压缩损伤评价[J]. 无损检测, 2011, 33(11): 29～32
共有人对该论文发表了看法，其中：
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】耿荣生，沈功田，刘时风.基于波形分析的声发射信号处理技术［J］.无损检测,2002,24(6):257-261.
【2】杨碧玲，张慧萍，晏雄.模式识别在复合材料声发射信号分析中的应用［J］.玻璃钢/复合材料,2007(2):51-53.
【3】方鹏，成来飞，张立同，等.C/SiC复合材料拉伸过程的声发射研究［J］.无损检测,2006,28(7):358-361.
【4】皇甫劭炜，童小燕，姚磊江，等.复合材料层合板损伤的声发射实验研究［J］.机械科学与技术,2009,28(5):669-673.
【5】Alander Pasi, Lassila Lippo V J, Tezvergil Arzu, et al. Acoustic emission analysis of fiber-reinforced composite in flexural testing［J］. Dental Materials,2004(20):305-312.
【6】SIRON Olivier, TSUDA Hiroshi. Acoustic emission in carbon fiber-reinforced plastic materials［J］. Carbon Fiber-Reinforced Plastic Materials,2000(25):533-537.
【7】Ravishankar S R, Murthy C R L. Application of acoustic emission in drilling of composite laminates［J］. NDT&E,2000(33):429-435.
【2】杨碧玲，张慧萍，晏雄.模式识别在复合材料声发射信号分析中的应用［J］.玻璃钢/复合材料,2007(2):51-53.
【3】方鹏，成来飞，张立同，等.C/SiC复合材料拉伸过程的声发射研究［J］.无损检测,2006,28(7):358-361.
【4】皇甫劭炜，童小燕，姚磊江，等.复合材料层合板损伤的声发射实验研究［J］.机械科学与技术,2009,28(5):669-673.
【5】Alander Pasi, Lassila Lippo V J, Tezvergil Arzu, et al. Acoustic emission analysis of fiber-reinforced composite in flexural testing［J］. Dental Materials,2004(20):305-312.
【6】SIRON Olivier, TSUDA Hiroshi. Acoustic emission in carbon fiber-reinforced plastic materials［J］. Carbon Fiber-Reinforced Plastic Materials,2000(25):533-537.
【7】Ravishankar S R, Murthy C R L. Application of acoustic emission in drilling of composite laminates［J］. NDT&E,2000(33):429-435.
相关信息
