Failure Analysis on Scuffing of Connecting Rod Bearing Shells of a Diesel
摘 要
采用宏观、微观、化学成分分析等多种检验方法对某柴油机连杆瓦台架磨合试验短时间后即发生咬死失效的原因进行了分析.结果表明:该连杆瓦咬死是由于柴油机油道清洁度不达标所致;结合其受力情况,认为连杆瓦初期磨损主要是因为机油中存在着较多的杂质颗粒造成连杆瓦表面拉伤,而下瓦由于工况更为恶劣因此剥落更为严重,其产生的剥落颗粒进一步加剧了上瓦磨损,最终导致连杆瓦发生咬死失效.
Abstract
The scuffing failure reasons of connecting rod bearing shells of a diesel after a short time of running-in bench test were analyzed by macro,micro and chemical compositions analysis.The results show that scuffing failure of the connecting rod bearing shells was mainly caused by the non-compliance cleanliness.Combining the force situation,it was considered that the early wear was mainly because there were a lot of impurities in the oil which induced surface scratch of the connecting rod bearing shells.The damage of the lower shell was more serious because of its bad working condition,and particles falling from the lower shell accelerated the wear of the upper shell,which finally resulted in scuffing failure of the connecting rod bearing shells.
中图分类号 TK427 TG115
所属栏目 质量控制与失效分析
基金项目
收稿日期 2014/2/13
修改稿日期
网络出版日期
作者单位点击查看
备注唐凯(1989-),男,助理工程师,学士.
引用该论文: TANG Kai,MEI Hong,GE Xiao-hong. Failure Analysis on Scuffing of Connecting Rod Bearing Shells of a Diesel[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2015, 51(2): 132~134
唐凯,梅红,葛晓红. 某柴油机连杆瓦咬死失效分析[J]. 理化检验-物理分册, 2015, 51(2): 132~134
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】郭亮,金献忠,黄世杰,等.铅黄铜阀芯部件开裂分析[J].理化检验-物理分册,2013,49(9):625-627.
【2】杜婷,周振新,李丽敏,等.扫描电镜中颗粒能谱定量分析的质量效应[J].理化检验-物理分册,2012,48(6):365-369,418.
【3】朱义.东风4B型内燃机车柴油机连杆瓦失效原因与预防措施[J].内蒙古科技与经济,2002(8):75-77.
【4】陈平.柴油机连杆轴瓦故障分析与修理[J].天津航海,2007(2):22-24.
【5】陈国兴.铜铅合金轴瓦镀三元合金前处理[J].电镀与环保,1995(3):31.
【2】杜婷,周振新,李丽敏,等.扫描电镜中颗粒能谱定量分析的质量效应[J].理化检验-物理分册,2012,48(6):365-369,418.
【3】朱义.东风4B型内燃机车柴油机连杆瓦失效原因与预防措施[J].内蒙古科技与经济,2002(8):75-77.
【4】陈平.柴油机连杆轴瓦故障分析与修理[J].天津航海,2007(2):22-24.
【5】陈国兴.铜铅合金轴瓦镀三元合金前处理[J].电镀与环保,1995(3):31.
相关信息