Effects of Extrusion Ratio on Microstructure and Tensile Properties of an Extruded Al-Fe-Cu Alloy
摘 要
采用热挤压成型工艺制备了Al-0.7Fe-0.2Cu-0.02B铝合金棒材, 研究了挤压比对其显微组织和拉伸性能的影响。结果表明: 合金在挤压变形过程中发生了动态再结晶, 随着挤压比增大, 再结晶晶粒细化, 且分布得更加均匀; 挤压变形后, 铸态合金中的网状第二相Al6Fe转变为Al3Fe, 随着挤压比增大, Al3Fe相逐渐细化并在晶界处聚集; 随着挤压比从6增大到28, 合金的抗拉强度从106.53 MPa增至122.67 MPa, 屈服强度从78.88 MPa增至84.65 MPa; 通过数据拟合得到挤压态合金屈服强度与平均晶粒尺寸的关系为σ0.2=63.8+77d-1/2。
Abstract
The effects of extrusion ratio on microstructure and tensile properties of Al-0.7Fe-0.2Cu-0.02B aluminum alloy bars which were produced by hot extrusion were studied. The results show that dynamic recrystallization occurred during hot extrusion, with the increase of the extrusion ratio, the recrystallization grains became smaller and more uniform distribution. After extrusion, the second phase Al6Fe transformed into Al3Fe, and the Al3Fe phase became small gradually and gathered at the grain boundaries with the increase of extrusion ratio. With the increase of extrusion ratio from 6 to 28,the tensile strength increased from 106.53 MPa to 122.67 MPa and the yield strength increased from 78.88 MPa to 84.65 MPa. The relationship between yield strength σ0.2 and mean grains size d of the extruded alloy obtained by data fitting was σ0.2=63.8+77d-1/2.
中图分类号 TG379
所属栏目 试验研究
基金项目 长沙市科技计划项目(K0902002-11)
收稿日期 2014/1/2
修改稿日期 2014/12/24
网络出版日期
作者单位点击查看
备注黄珂(1989-), 男, 湖南长沙人, 硕士研究生。
引用该论文: HUANG Ke,GUO Lei,YANG Fu-liang,MA Kai,LIU Peng,LIU Gong-qi. Effects of Extrusion Ratio on Microstructure and Tensile Properties of an Extruded Al-Fe-Cu Alloy[J]. Materials for mechancial engineering, 2015, 39(4): 53~58
黄珂,郭磊,杨伏良,马凯,刘鹏,柳公器. 挤压比对热挤压成型铝铁铜合金组织与拉伸性能的影响[J]. 机械工程材料, 2015, 39(4): 53~58
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】贺毅强, 乔斌, 王娜, 等. 不同拉伸温度下SiC颗粒增强Al-Fe-V-Si复合材料的断裂行为[J].中国有色金属学报, 2010, 20(3):469-475.
【2】徐永利, 季道馨, 陈昌麒. Al-Fe-V-Si合金工艺探讨[J].材料工程, 1993, 9(3):43-47.
【3】谭敦强, 黎文献, 唐谊平. Al-Fe系合金中的相及相转变[J].材料导报, 2003, 17(5):18-20.
【4】KOSUGE H, MIZUKAMI I. Formation of “Fir-Tree” structure in D.C. cast ingots of Al-0.6percent Fe alloys[J].J Jap Inst Light Met, 1975, 25(2):48-58.
【5】董寅生,沈军,杨英俊.快速凝固耐热铝合金中的弥散相及其热稳定性[J].宇航材料工艺, 2000, 30(2):1-6.
【6】仝兴存,沈宁福,柳百成.快速凝固Al-Fe-Ti-C合金的显微结构及退火过程中的相变[J].金属学报, 1994, 30(3):134-138.
【7】王祝堂.铝合金及其加工手册[M].长沙: 中南大学出版社, 2000.
【8】张振栋, 刘楚明, 常亚喆, 等. 挤压次数对Mg-Zn-Zr-Re合金组织和性能的影响[J].中南大学学报: 自然科学版, 2008, 39(2): 228-233.
【9】汤亚力, 沈宁福, 张东捷,等. Al-8Fe-3Ti急冷合金的组织稳定性[J].郑州工院院学报, 1995, 16(1):87-91.
【10】SRINIVAS V, BARUA P, MURTY B S. On icosahedral phase formation in mechanically alloyed Al70Cu20Fe10[J]. Materials Science and Engineering, 2000, 294/296:65-67.
【11】KLEIN T, SYMKO O G. Formation of AlCuFe quasicrystalline thin film by solid state diffusion[J].Applied Physics Letters, 1994, 64(4):431-433.
【12】林高用, 张胜华, 胡泽豪. 2024铝合金挤压过程动态再结晶问题的研究[J].兵器材料科学与工程, 2000, 23(1):40-45.
【13】王斌,,易丹青.稀土元素Y 和Nd对Mg-Zn-Zr系合金组织和性能的影响[J].金属热处理, 2005, 30(7): 9-13.
【14】张雷, 孟亮. 合金元素对Cu-Ag合金组织、力学性能和电学性能的影响[J].中国有色金属学报, 2002, 12(6):1218-1223.
【15】石其年.二次挤压对Al-Li合金组织及性能的影响[J].热加工工艺, 2006, 35(8): 34-39.
【2】徐永利, 季道馨, 陈昌麒. Al-Fe-V-Si合金工艺探讨[J].材料工程, 1993, 9(3):43-47.
【3】谭敦强, 黎文献, 唐谊平. Al-Fe系合金中的相及相转变[J].材料导报, 2003, 17(5):18-20.
【4】KOSUGE H, MIZUKAMI I. Formation of “Fir-Tree” structure in D.C. cast ingots of Al-0.6percent Fe alloys[J].J Jap Inst Light Met, 1975, 25(2):48-58.
【5】董寅生,沈军,杨英俊.快速凝固耐热铝合金中的弥散相及其热稳定性[J].宇航材料工艺, 2000, 30(2):1-6.
【6】仝兴存,沈宁福,柳百成.快速凝固Al-Fe-Ti-C合金的显微结构及退火过程中的相变[J].金属学报, 1994, 30(3):134-138.
【7】王祝堂.铝合金及其加工手册[M].长沙: 中南大学出版社, 2000.
【8】张振栋, 刘楚明, 常亚喆, 等. 挤压次数对Mg-Zn-Zr-Re合金组织和性能的影响[J].中南大学学报: 自然科学版, 2008, 39(2): 228-233.
【9】汤亚力, 沈宁福, 张东捷,等. Al-8Fe-3Ti急冷合金的组织稳定性[J].郑州工院院学报, 1995, 16(1):87-91.
【10】SRINIVAS V, BARUA P, MURTY B S. On icosahedral phase formation in mechanically alloyed Al70Cu20Fe10[J]. Materials Science and Engineering, 2000, 294/296:65-67.
【11】KLEIN T, SYMKO O G. Formation of AlCuFe quasicrystalline thin film by solid state diffusion[J].Applied Physics Letters, 1994, 64(4):431-433.
【12】林高用, 张胜华, 胡泽豪. 2024铝合金挤压过程动态再结晶问题的研究[J].兵器材料科学与工程, 2000, 23(1):40-45.
【13】王斌,,易丹青.稀土元素Y 和Nd对Mg-Zn-Zr系合金组织和性能的影响[J].金属热处理, 2005, 30(7): 9-13.
【14】张雷, 孟亮. 合金元素对Cu-Ag合金组织、力学性能和电学性能的影响[J].中国有色金属学报, 2002, 12(6):1218-1223.
【15】石其年.二次挤压对Al-Li合金组织及性能的影响[J].热加工工艺, 2006, 35(8): 34-39.
相关信息