Calculation of the Gap between Wedge Block and the Detection Surface while Scanning on the Curvature Surfaces
摘 要
超声波检测时,楔块表面与被测工件表面应耦合.当被测工件表面如管道、球罐等曲面时,楔块表面与被测工件表面应满足相应的耦合条件.分析了标准GB/T 11345-1989《钢焊缝手工超声波探伤方法和探伤结果分级》和标准GB/T 11345-2013《焊缝无损检测超声检测技术、检测等级和评定》对于楔块与工件表面耦合要求的异同,对不同曲率楔块与曲率工件表面之间的接触方式进行了几何分析,推导出计算平面/曲面楔块与工件间隙的精确公式,为检测工作中楔块的选取提供了参考依据.
Abstract
On Ultrasonic testing,the wedge block and workpiece surface should be well coupled.When the workpiece surface is flat,just plane wedge can be used to meet the workpiece surface coupling requirement,and for the workpiece such as pipeline and spherical tank,the wedge surface and the workpiece surface should meet the corresponding coupling condition.This paper analyzes the wedge-workpiece surface coupling requirement in GB 11345-1989 and GB 11345-2013,the similarities and differences.Geometric analysis was made for different contact types between wedges and curvature workpiece surface,and the precise formula for calculating the gaps between plane / curvature surface wedge block and the workpiece is derived,thus providing a reference for the selection of suitable wedges.
中图分类号 TB552 DOI 10.11973/wsjc201506002
所属栏目 GB/T11345-2013系列标准评析专题
基金项目
收稿日期 2015/1/23
修改稿日期
网络出版日期
作者单位点击查看
备注吴昊(1982-),男,高级工程师,主要从事超声波无损检测研究工作.
引用该论文: WU Hao,YANG Yu-qing,LUO Xiao-ming. Calculation of the Gap between Wedge Block and the Detection Surface while Scanning on the Curvature Surfaces[J]. Nondestructive Testing, 2015, 37(6): 5~7
吴昊,杨宇清,罗晓明. 曲面扫查时楔块与检测面间隙的计算方法[J]. 无损检测, 2015, 37(6): 5~7
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】文毅,冯强,李燕.超声检测在管道焊缝腐蚀中的应用[J].无损检测,2014,36(2):50-52.
【2】周以琳.管道超声无损检测技术的研究与应用[M].青岛:青岛科技大学出版社,2011:1.
【3】李衍.小径薄壁管道超声相控阵检测[J].无损探伤,2015(1):1-5.
【4】魏同锋.小口径管道超声波检测耦合曲面修正系数[J].油气储运,2014(6):629-631,652.
【2】周以琳.管道超声无损检测技术的研究与应用[M].青岛:青岛科技大学出版社,2011:1.
【3】李衍.小径薄壁管道超声相控阵检测[J].无损探伤,2015(1):1-5.
【4】魏同锋.小口径管道超声波检测耦合曲面修正系数[J].油气储运,2014(6):629-631,652.
相关信息