Effect of Crack Length and Lift-Off Distance on Eddy Current Sensor Array′s Output Characteristics
摘 要
分析了涡流阵列检测技术的基本原理,利用有限元方法建立了一种涡流阵列传感器的仿真模型,分析了裂纹长度和提离距离对传感器输出特性的影响.结果表明,裂纹的出现会导致感应线圈输出信号的幅值和相位发生变化,随着裂纹长度的增加,感应线圈的输出信号幅值和相位逐渐增加;随着提离距离的增加,传感器的输出信号幅值和相位也急剧增加.将该传感器应用于裂纹长度检测时,应尽量抑制提离距离的波动.
Abstract
The basic principles of eddy current array inspecting method were analyzed at first.Then a simulation model of an eddy current array probe was established based on finite element method.The influences of crack length and lift-off distance on output characteristics were analyzed.It was shown that there would be a change on amplitude and phase of output signal when a crack appeared below the footprint of sensing coil in metal structures,and the amplitude and phase of sensing coil was increasing gradually as crack propagation.Besides,there would be a sharp increment of amplitude and phase as lift-off distance increased.The sensor could be applied in crack inspection and distance measurement,but the variation of lift-off distance should be restricted in crack inspecting.
中图分类号 TG115.28 TP212.1 DOI 10.11973/wsjc201507009
所属栏目 试验研究
基金项目 国家高技术研究发展计划资助项目(2009AA04Z406)
收稿日期 2014/10/28
修改稿日期
网络出版日期
作者单位点击查看
备注杜金强(1984-),男,博士,讲师,主要从事飞机结构健康监控技术研究工作.
引用该论文: DU Jin-qiang,SHI Yue-hong,HE Yu-ting. Effect of Crack Length and Lift-Off Distance on Eddy Current Sensor Array′s Output Characteristics[J]. Nondestructive Testing, 2015, 37(7): 36~39
杜金强,施越红,何宇廷. 裂纹长度和提离距离对涡流阵列传感器输出特性的影响[J]. 无损检测, 2015, 37(7): 36~39
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】李家伟,陈积懋.无损检测手册[M].北京:机械工业出版社,2006.
【2】韩亚利,陈勇,周志平.应用涡流电导率检测技术评定铝合金的热损伤[J].航空精密制造技术,2006,42(3):37-40.
【3】张思全,陈铁群,刘桂雄.应力腐蚀裂纹涡流检测信号的处理及形状重构[J].核动力工程,2008,29(6):50-53.
【4】TOSHIHIKO Y,MASAHIRO U.An Active sensor for monitoring bearing wear by means of an eddy current displacement sensor[J]. Measurement Science and Technology,2007,18:311-317.
【5】周俊华,徐可北,葛子亮.热障涂层厚度涡流检测技术研究[J].航空材料学报,2006,26(3):353-356.
【6】赵磊.阵列涡流无损检测技术的研究及进展[J].无损探伤,2009,33(2):19-22.
【7】付小强,吴素君,张佳佳.涡流阵列无损检测技术在大飞机中的应用[J].民用飞机设计与研究,2009(S1):84-88.
【8】丁天怀,陈祥林.电涡流传感器阵列测试技术[J].测试技术学报,2006,20(1):1-5.
【9】楼敏珠,郭韵.基于涡流阵列传感器的高强度螺栓扫描检测成像系统设计[J].无损检测,2009,31(6):485-487.
【10】陈祥林,丁天怀,黄毅平.新型接近式柔性电涡流阵列传感器系统[J].机械工程学报,2006,42(8):150-153.
【11】唐莺,罗飞路,潘孟春.基于有限元法的涡流传感器设计[J].无损检测,2008,30(11):804-806.
【12】辛伟,丁克勤,黄冬林.带保温层管道腐蚀缺陷的脉冲涡流检测技术仿真[J].无损检测,2009,31(7):509-513.
【13】阎照文.ANSYS10.0工程电磁分析技术与实例详解[M].北京:中国水利水电出版社,2006.
【14】YANKO S,DAVE G,VLADIMIR Z.MWM-array sensors for in situ monitoring of high-temperature components in power plants[J].IEEE Sensors Journal,2009,9(11):1527-1536.
【15】杜金强,何宇廷,丁华.基于涡流阵列的裂纹检测仿真分析[J].无损检测,2011,33(7):21-24.
【2】韩亚利,陈勇,周志平.应用涡流电导率检测技术评定铝合金的热损伤[J].航空精密制造技术,2006,42(3):37-40.
【3】张思全,陈铁群,刘桂雄.应力腐蚀裂纹涡流检测信号的处理及形状重构[J].核动力工程,2008,29(6):50-53.
【4】TOSHIHIKO Y,MASAHIRO U.An Active sensor for monitoring bearing wear by means of an eddy current displacement sensor[J]. Measurement Science and Technology,2007,18:311-317.
【5】周俊华,徐可北,葛子亮.热障涂层厚度涡流检测技术研究[J].航空材料学报,2006,26(3):353-356.
【6】赵磊.阵列涡流无损检测技术的研究及进展[J].无损探伤,2009,33(2):19-22.
【7】付小强,吴素君,张佳佳.涡流阵列无损检测技术在大飞机中的应用[J].民用飞机设计与研究,2009(S1):84-88.
【8】丁天怀,陈祥林.电涡流传感器阵列测试技术[J].测试技术学报,2006,20(1):1-5.
【9】楼敏珠,郭韵.基于涡流阵列传感器的高强度螺栓扫描检测成像系统设计[J].无损检测,2009,31(6):485-487.
【10】陈祥林,丁天怀,黄毅平.新型接近式柔性电涡流阵列传感器系统[J].机械工程学报,2006,42(8):150-153.
【11】唐莺,罗飞路,潘孟春.基于有限元法的涡流传感器设计[J].无损检测,2008,30(11):804-806.
【12】辛伟,丁克勤,黄冬林.带保温层管道腐蚀缺陷的脉冲涡流检测技术仿真[J].无损检测,2009,31(7):509-513.
【13】阎照文.ANSYS10.0工程电磁分析技术与实例详解[M].北京:中国水利水电出版社,2006.
【14】YANKO S,DAVE G,VLADIMIR Z.MWM-array sensors for in situ monitoring of high-temperature components in power plants[J].IEEE Sensors Journal,2009,9(11):1527-1536.
【15】杜金强,何宇廷,丁华.基于涡流阵列的裂纹检测仿真分析[J].无损检测,2011,33(7):21-24.
相关信息