搜索热:失效分析 陶瓷
扫一扫 加微信
首页 > 期刊论文 > 论文摘要
锰加入量对铝合金中富铁相形貌和电磁过滤的影响
          
Influence of Manganese Addition on Iron-rich Phase Shape and Electromagnetic Filtration of Al-Fe Alloy

摘    要
将不同数量的锰添加到Al-2%Fe合金中,进行电磁过滤并浇注试样,研究了合金中富铁相的形貌和力学性能.结果表明:初生Al3Fe相的形貌发生了明显的变化,当锰、铁的摩尔比为1.3~1.5时,针状的富铁相基本消失,取而代之的是块状.锰变质后,抗拉强度比变质前的126 MPa提高了20~30 MPa,伸长率达到22.9%.变质的熔体通过电磁过滤后,由于铁相基本上被去除,合金的伸长率可以达到29.2%,而抗拉强度降低为131 MPa.
标    签 富铁相   抗拉强度   伸长率   电磁过滤   iron-rich phase   tensile strength   elongation   electromagnetic filtration  
 
Abstract
Through adding different contents of Mn into Al-2%Fe alloy,carrying through electromagnetic experiment and casing samples,the morphology of the primary Al3Fe phase and mechanical properties were investigated.Mn has obvious influence on the shape of iron-rich phase,which changed from the needle-like to needle plate-like and particle-like.When the molar ratio of Mn/Fe=1.3-1.5,the modifying effect is the best.The tensile strength is raised by 20-30 MPa after adding Mn,the tensile strength is 126 MPa without Mn,the elongation is up to 22.9%.After the modified melt was acted in magnetic filed,the iron-rich phase move to the pipe wall and is removed because of the electromagnetic repulsion force.The melt is mainly aluminum.Therefore the tensile strength declined to 131 MPa,but the elongation is enhanced further,up to 29.2%.

中图分类号 TG146.2 TG292

 
  中国光学期刊网论文下载说明


所属栏目

基金项目 国家自然科学基金资助项目(50274018)

收稿日期 2006/8/7

修改稿日期 2006/11/4

网络出版日期

作者单位点击查看

备注陈东风(1980-),男,河南商丘人,硕士研究生.

引用该论文: CHEN Dong-feng,CAO Zhi-qiang,ZHANG Ting. Influence of Manganese Addition on Iron-rich Phase Shape and Electromagnetic Filtration of Al-Fe Alloy[J]. Materials for mechancial engineering, 2007, 31(6): 42~45
陈东风,曹志强,张婷. 锰加入量对铝合金中富铁相形貌和电磁过滤的影响[J]. 机械工程材料, 2007, 31(6): 42~45


被引情况:


【1】刘扭参,杨安杰,李俊青,刘忠侠,杨明生, "过滤对电热法制备ZL102合金显微组织和力学性能的影响",机械工程材料 34, 45-47(2010)



论文评价
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
分享论文
分享到新浪微博 分享到腾讯微博 分享到人人网 分享到 Google Reader 分享到百度搜藏分享到Twitter

参考文献
【1】印飞,杨江波,孙宝德.铝硅合金中的六角形铁相[J].上海交通大学学报,2001,35(3):477-480.
 
【2】Narayanan L A,Samuel F H,Gruzleski J E.Crystal2lization behavior of iron-containing inter-metallic compound in 319 aluminum alloy[J].Metallurgy and Materials Transactions A,1992,25A:1761-1766.
 
【3】Sigworth G K,Shivkuman S,Apelian D.The influence of molten metal processing on mechanical properties of cast Al-Si-Mg alloy[J].AFS Transactions,1989,139:811-824.
 
【4】Awano Y,Shimizu Y.Non-equilibrium crystallization of AlSiFe compound in melt-superheated Al-Si alloy casting[J].AFS Transactions,1990,176:889-896.
 
【5】Couture A.Iron in aluminum casting alloys——A literature survey[J].AFS Transactions,1981,11:9-17.
 
【6】Muali S,Raman K S,Murthy K S S.Morphological studies on β-FeSiAl5 phase in Al-7Si-0.3Mg alloy with trace addition of Be,Mn,Cr and Co[J].Materials Characterization,1994,33:99-112.
 
【7】疏达,孙宝德,李天晓,等.铝熔体中夹杂物形状与取向对其电磁分离的影响[J].金属学报,2000,36(9):9562-9601.
 
【8】李克,孙宝德,疏达,等.利用高频磁场连续分离铝熔体中非金属夹杂的实验研究[J].金属学报,2001,37(4):405-410.
 
【9】钟云波,任忠鸣,邓康,等.行波磁场净化液态金属时矩形管及三角管内夹杂除去效率的理论分析[J].金属学报,1999,5(5):503-508.
 
【10】朴杓,森平淳志,佐々健介,等.电磁力を利用した溶融金属中介在物の除去[J].铁と钢,1994,80(5):31-36.
 
【11】李克,孙宝德,李天晓,等.利用高频磁场分离Al熔体中的金属夹杂[J].金属学报,2001,37(4):405-410.
 
【12】Mondolfo L Fed,Translated by Wang Z T,Zhang Z L,et al.Structures and properties of aluminum alloys[M].Beijing:Metallurgy Industry Press,1998.
 
相关信息
   标题 相关频次
 电磁连铸Al-1%Si棒材的组织和力学性能
 4
 锰配分温度对I&Q&P处理后低碳硅锰钢组织与力学性能的影响
 4
 2A70铝合金搅拌摩擦焊接头抗拉强度测定结果的不确定度评定
 2
 3003铝合金薄板超高转速搅拌摩擦焊接头的组织与性能
 2
 304不锈钢室温抗拉强度测试的影响因素
 2
 3PE防腐蚀层联合阴极保护对管道的保护效果
 2
 7050铝合金表面氧化膜厚度对其搅拌摩擦焊焊接接头性能的影响
 2
 7050铝合金均匀化工艺的确定
 2
 Al-Mg-Si系铝合金的成分设计
 2
 D406A钢和20钢异质接头的显微组织和力学性能
 2
 DH32船板钢埋弧焊接头的力学性能
 2
 DP590带钢屈服和抗拉强度的微磁定量预测
 2
 Er含量对汽车发动机用AM50合金组织与耐蚀性的影响
 2
 H18热处理态2024铝合金的高温流变性能
 2
 IF热轧钢板拉伸试验结果的测量不确定度评定
 2
 P110石油套管水压试验开裂原因分析
 2
 Q235钢抗拉强度测量不确定度评定
 2
 S32101双相不锈钢晶间腐蚀试验裂纹判定
 2
 SG90T-9C高强韧性渣气联保药芯焊材的研发
 2
 Ti2AlNb合金的高温拉伸变形行为
 2
 ZG06Cr13Ni4Mo不锈钢材料抗拉强度与布氏硬度的关系
 2
 板对接接头拉伸试样几何尺寸对其抗拉强度的影响
 2
 苯胺装置循环废酸泵的选材
 2
 变厚度碳纤维/环氧树脂基复合材料层压板的多电子闸门C扫成像
 2
 标距对电工圆铜线拉力试验结果的影响
 2
 表面机械处理对5083铝合金表面形貌和拉伸性能的影响
 2
 玻璃钢抽油杆断裂原因分析
 2
 薄板熔化焊的最佳熔深
 2
 不同玻璃纤维单向增强树脂基复合材料的疲劳行为
 2
 不同形状搅拌头异种铝合金搅拌摩擦焊接头的性能
 2