Solid-liquid Mixed Die-casting of Al-10%Cr Alloy
摘 要
采用固液混合压铸工艺制备了Al-10%Cr合金,用光学显微镜、密度测量仪、硬度计、拉伸试验机和摩擦试验机等对合金的组织和性能进行了分析.结果表明:该工艺获得的高铬铝合金坯料显微组织均匀,晶粒细小呈近等轴状,密度为2.924 g·cm-3;热挤压后合金的抗拉强度σb为119 MPa,屈服强度σ0.2为89 MPa,伸长率δ为1%,磨损率为16.9 mg·m-1,均优于传统铸造和半固态铸造所得相同成分合金的;该工艺使Al-10%Cr合金的工业应用成为可能.
Abstract
Solid-liquid mixed die-casting technology was applied to prepare Al-10%Cr alloy.The microstructure and properties were studied by means of optical microscopy,densimeter and sclerometer etc.The results show that the grains can be obviously refined with near-spherical shape and the density is 2.924 g·cm-3.The optimum properties after hot extrusion were σb=119 MPa,σ0.2=89 MPa,δ=1%,and the wear rate was 169 mg·m-1,which were preferable to those alloys with the same chemical composition prepared by conventional casting and semi-solid casting.Thus,the Al-10%Cr alloy has the possibility to be used in the industry.
中图分类号 TG146.2 TG249.2
所属栏目 新材料 新工艺
基金项目 国家自然科学基金资助项目(50274037)
收稿日期 2007/12/5
修改稿日期 2008/4/21
网络出版日期
作者单位点击查看
备注刘劲松(1967-),女,湖南邵阳人,副教授,博士研究生.
引用该论文: LIU Jing-song,CHEN Zhen-hua,PU Yu-xing,LI Jian-yue,HE Jian-jun. Solid-liquid Mixed Die-casting of Al-10%Cr Alloy[J]. Materials for mechancial engineering, 2009, 33(1): 30~32
刘劲松,陈振华,蒲玉兴,李建跃,何建军. Al-10%Cr合金的固液混合压铸工艺[J]. 机械工程材料, 2009, 33(1): 30~32
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】王祝堂.铝合金及其加工手册[M].长沙:中南大学出版社,1988.
【2】陈振华,严红革,陈刚,等.合金和复合材料的固液混合铸造技术:中国: ZL01106868X[P].2001.
【3】陈振华,陈鼎,严红革,等.固液混合铸造的研究[J].湖南大学学报,2002,29(4):20-26.
【4】陈振华.Al-Si合金固液混合铸造[J].中国有色金属学报,2000,10(6):349.
【5】陈振华,严红革,陈刚,等.耐热铝合金固液混合铸造[J].中国有色金属学报,2002,12(3):422-425.
【6】吴艳军.A-8.7Fe-1.6V-1.3Si 固液混合铸造组织及性能研究[D].长沙:中南大学,2000.
【7】杨为佑.Al-Si 固液混合铸造组织及性能研究[D].长沙:中南大学,2001.
【8】刘劲松,龙小兵,何建军,等.悬浮铸造、半固态铸造与固液混合铸造[J].长沙航空职业技术学院学报,2003,3(1):56-59.
【2】陈振华,严红革,陈刚,等.合金和复合材料的固液混合铸造技术:中国: ZL01106868X[P].2001.
【3】陈振华,陈鼎,严红革,等.固液混合铸造的研究[J].湖南大学学报,2002,29(4):20-26.
【4】陈振华.Al-Si合金固液混合铸造[J].中国有色金属学报,2000,10(6):349.
【5】陈振华,严红革,陈刚,等.耐热铝合金固液混合铸造[J].中国有色金属学报,2002,12(3):422-425.
【6】吴艳军.A-8.7Fe-1.6V-1.3Si 固液混合铸造组织及性能研究[D].长沙:中南大学,2000.
【7】杨为佑.Al-Si 固液混合铸造组织及性能研究[D].长沙:中南大学,2001.
【8】刘劲松,龙小兵,何建军,等.悬浮铸造、半固态铸造与固液混合铸造[J].长沙航空职业技术学院学报,2003,3(1):56-59.
相关信息