赛隆陶瓷注射成型喂料的流变性能
Rheological Characteristics of Feedstock for Sialon Ceramic Injection Molding
摘 要
用毛细管流变仪测试了赛隆陶瓷注射成型用喂料在不同温度、不同剪切应变速率下的黏度,对喂料的流变性能进行了研究,分析了黏度对剪切应变速率和温度的敏感性,研究了注射温度对成型坯体的质量影响.结果表明:该喂料在高温下具有非牛顿假塑性流变行为,具有良好的充模性,在不同温度下的非牛顿指数n值皆小于1;在130 ℃时喂料的n值最小,为0.393 2,流变稳定性最好,所以注射成型坯体的质量最好.
黏度
喂料
流变性能
ceramic injection molding
viscosity
feedstock
rheology property
Abstract
The viscosities of the feedstock using for Sialon ceramic injection molding at different temperatures and the rates of shear strain were investigated by capillary rheometer.The rheological property of the feedstock was analyzed.The sensitivity of the viscosity on the rate of shear strain and the temperature was studied,the effect of injection temperature on the quality of green parts was also discussed.The results show that the feedstock showed non-Newtonian pseudoplastic rheological behavior at high temperatures,and had good moldability.The non-Newtonian index (n) at different temperatures was determined to be less than 1.The minimal n value of feedstock was 0.393 2 at 130 ℃,and the best injection molding quality and the rheological stability could be obtained.
中图分类号 TQ174
所属栏目 新材料 新工艺
基金项目 国防科学技术工业委员会基础科研项目(A2520060236)
收稿日期 2007/11/26
修改稿日期 2009/2/27
网络出版日期
作者单位点击查看
备注颜平(1982-),女,山东济宁人,硕士研究生.
引用该论文: YAN Ping,LIU Jun,CHEN Ping,CHEN Cai-feng. Rheological Characteristics of Feedstock for Sialon Ceramic Injection Molding[J]. Materials for mechancial engineering, 2009, 33(5): 80～82
颜平,刘军,陈萍,陈彩凤. 赛隆陶瓷注射成型喂料的流变性能[J]. 机械工程材料, 2009, 33(5): 80～82
共有人对该论文发表了看法，其中：
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】IMENEZ J,BAGHERI O,MCCLAIN H,et al.Final design and test of a ceramic hot section[J].ASME Turbo Expo,Land,Sea & Air,2003(6):16-19.
【2】CALOMINO A,VERRILLI M J.Ceramic matrix composite vane subelement fabrication[J].ASME Turbo Expo,Land,Sea & Air,2004(6):14-16.
【3】BILL T,SHI Jun,JOHN H,et al.Design of ceramic components for an advanced micro-turbine engine[J].ASME Turbo Expo,Land,Sea & Air,2004(6):16-17.
【4】王秀,谢志鹏,李建保,等.工程陶瓷注射成型的研究与发展[J].稀有金属材料与工程,2004,33(11):1121-1126.
【5】谢志鹏,罗杰盛,李建保.陶瓷注射成型研究进展[J].陶瓷科学与艺术,2003(5):16-18.
【6】KARATAS C,KOCER A,NAL H I,et al.Rheological properties of feedstocks prepared with steatite power and polyethylene-based thermoplastic binders[J].Journal of Materials Processing Technology,2004,152:77-83.
【7】PALCEVSKIS E,FAITELSON L,JAKOBSONS E.Rheology of organodispersions of alumina nanopowders used in producing articles from engineering ceramics[J].Mechanics of Composite Materials,2005,41(3):255-266.
【8】梁叔全,黄伯云.粉末注射成形流变学[M].长沙:中南大学出版社,2000.
【9】GERMAN R M.粉末注射成形[M].曲选辉,译.长沙:中南大学出版社,2001:122-132.
【10】张娇月,徐军,司文捷,等.陶瓷注射成型用PVB树脂基粘结剂研究[J].材料科学与工程学报,2005,23(1):27-30.
【11】KRYACHEK V M.Injection molding(review)[J].Power Metallurgy and Metal Ceramics,2004,43:336-348.
【2】CALOMINO A,VERRILLI M J.Ceramic matrix composite vane subelement fabrication[J].ASME Turbo Expo,Land,Sea & Air,2004(6):14-16.
【3】BILL T,SHI Jun,JOHN H,et al.Design of ceramic components for an advanced micro-turbine engine[J].ASME Turbo Expo,Land,Sea & Air,2004(6):16-17.
【4】王秀,谢志鹏,李建保,等.工程陶瓷注射成型的研究与发展[J].稀有金属材料与工程,2004,33(11):1121-1126.
【5】谢志鹏,罗杰盛,李建保.陶瓷注射成型研究进展[J].陶瓷科学与艺术,2003(5):16-18.
【6】KARATAS C,KOCER A,NAL H I,et al.Rheological properties of feedstocks prepared with steatite power and polyethylene-based thermoplastic binders[J].Journal of Materials Processing Technology,2004,152:77-83.
【7】PALCEVSKIS E,FAITELSON L,JAKOBSONS E.Rheology of organodispersions of alumina nanopowders used in producing articles from engineering ceramics[J].Mechanics of Composite Materials,2005,41(3):255-266.
【8】梁叔全,黄伯云.粉末注射成形流变学[M].长沙:中南大学出版社,2000.
【9】GERMAN R M.粉末注射成形[M].曲选辉,译.长沙:中南大学出版社,2001:122-132.
【10】张娇月,徐军,司文捷,等.陶瓷注射成型用PVB树脂基粘结剂研究[J].材料科学与工程学报,2005,23(1):27-30.
【11】KRYACHEK V M.Injection molding(review)[J].Power Metallurgy and Metal Ceramics,2004,43:336-348.
相关信息
