Microstructure and Depth of Harden Layer of 40Cr Steel Melting Treated with Different Lasers
摘 要
分别采用轴流和横流CO2激光器对40Cr钢进行熔凝硬化处理,利用扫描电镜和显微硬度计分析了不同工艺参数下熔凝硬化层的显微组织及深度.结果表明:两种激光器熔凝处理后的硬化层均由相变硬化区和过渡区组成;两个区的显微组织分别为混合马氏体+残余奥氏体和回火马氏体+残余奥氏体+铁素体+珠光体+碳化物;经过两种激光器处理后的硬化层深度都随着能量密度的增加而增大;横流CO2激光器处理后的硬化层深度比轴流CO2激光器处理后的更深.
Abstract
The surface of 40Cr steel was treated by melting hardening with the axial flow CO2 laser and the transversal flow CO2 laser respectively.The microstructure and depth of melting hardened layers was analyzed by means of scanning electron microscope and microhardeness sclerometer.The results show that the melting hardened layer treated by axis flow and transversal flow CO2 laser both consisted of hardening zone and transient zone.The microstructure of the two zones was mixed martensite + retained austenite,and tempered martensite + retained austenite + ferrite + pearlite + carbide.The depth of the hardened layer treated by these two lasers both increased with the increase of energy density.The depth of hardened layer treated by transversal flow CO2 laser was deeper than that treated by the axis flow CO2 laser.
中图分类号 TG156.99
所属栏目 材料性能及其应用
基金项目 大连理工大学三束材料改性国家重点实验室开放课题资助(0601)
收稿日期 2008/6/19
修改稿日期 2008/9/16
网络出版日期
作者单位点击查看
备注李刚(1969-),男,辽宁阜新人,教授,博士.
引用该论文: LI Gang,QIU Ling,QIU Xing-wu. Microstructure and Depth of Harden Layer of 40Cr Steel Melting Treated with Different Lasers[J]. Materials for mechancial engineering, 2009, 33(6): 77~80
李刚,邱玲,邱星武. 不同激光器熔凝处理40Cr钢硬化层的显微组织及深度[J]. 机械工程材料, 2009, 33(6): 77~80
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】李艳芳,卫英慧,胡兰青,等.金属材料表面激光热处理的研究与应用[J].太原理工大学学报,2002,33(2):142-146.
【2】罗玉梅.激光淬火工艺的现状及应用[J].邵阳学院学报,2004(3):51-53.
【3】刘江龙,邹至荣,苏宝嫆.高能束热处理[M].北京:机械工业出版社,1997:187-188.
【4】姜幼卿,黄安国,周龙早,等.冶金用铸钢轧辊激光熔凝强化的研究和应用[J].中国机械工程,2006,17(1):1756-1758.
【5】叶云霞,符永宏,杨国成,等.快速轴流CO2激光器激光相变硬化处理HT250的研究[J].中国激光,2002,29(10):946-947.
【2】罗玉梅.激光淬火工艺的现状及应用[J].邵阳学院学报,2004(3):51-53.
【3】刘江龙,邹至荣,苏宝嫆.高能束热处理[M].北京:机械工业出版社,1997:187-188.
【4】姜幼卿,黄安国,周龙早,等.冶金用铸钢轧辊激光熔凝强化的研究和应用[J].中国机械工程,2006,17(1):1756-1758.
【5】叶云霞,符永宏,杨国成,等.快速轴流CO2激光器激光相变硬化处理HT250的研究[J].中国激光,2002,29(10):946-947.
相关信息