Microstructure and Properties Comparison of Laser Cladding Layer and Spraying Layer of Ni-Based Self-Fluxing Alloy
摘 要
对Ni60镍基自熔合金激光熔覆层和喷焊层的表面形貌、显微组织、硬度和耐腐蚀性能等进行了对比分析.结果表明:激光熔覆层的表面成型性比喷焊层的好;大部分激光熔覆层组织处于非平衡、亚结晶状态,且具有强、韧两相微观结构特征;喷焊层组织中富含碳化物等硬质相;激光熔覆层和喷焊层与基体均能形成冶金结合;喷焊层的平均硬度比激光熔覆层的高,但其分布并不均匀;激光熔覆层的耐腐蚀性能优于喷焊层的.
Abstract
The surface morphology,microstructure,micro-hardness and corrosion resistance of the laser cladding layer and spraying layer of the Ni60 Ni-based self-fluxing alloy were analyzed and compared.The results show that the surface forming performance of the laser cladding layer was better than that of the spraying layer.The microstructure of the laser cladding layer was mostly in non-equilibrium and sub-crystalline state,and had a strong and tough two-phase microstructure characteristics.The microstructure of the spraying layer was rich in the hard phase of carbides.Both the laser cladding layer and the spraying layer could get a metallurgy bonding with the substrate.Although the average micro-hardness of the spraying layer was higher than that of the laser cladding layer,its distribution was not uniform.And the corrosion resistance of the laser cladding layer was superior to that of the spraying layer.
中图分类号 TG665 TU512.9
所属栏目 材料性能及其应用
基金项目 山西省回国留学人员科研基金资助项目(2007-34)
收稿日期 2009/10/27
修改稿日期 2010/6/3
网络出版日期
作者单位点击查看
备注冯旭东(1985-),男,河南登封人,硕士研究生.
引用该论文: FENG Xu-dong,YUAN Qing-long,CAO Jing-jing,SU Zhi-jun. Microstructure and Properties Comparison of Laser Cladding Layer and Spraying Layer of Ni-Based Self-Fluxing Alloy[J]. Materials for mechancial engineering, 2010, 34(11): 73~78
冯旭东,袁庆龙,曹晶晶,苏志俊. 镍基自熔合金激光熔覆层和喷焊层的组织与性能对比[J]. 机械工程材料, 2010, 34(11): 73~78
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】潘邻.激光表面改性的现状和展望[J].表面工程资讯,2005,5(1):5-6.
【2】SUN R L,YANG D Z,GUO L X,et al.Microstructure and wear resistance of NiCrBSi laser clad layer on titanium alloy substrate[J].Surface and Coatings Technology,2000,132(2/3):251-255.
【3】李明喜,何宜柱,孙国雄.Ni基合金/45钢宽、窄带熔覆Co基合金的组织[J].中国激光,2003,30(11):1044-1048.
【4】ZHOU Sheng-feng,HUANG Yong-jun,ZENG Xiao-yan.Microstructure characteristics of Ni-based WC composite coatings by laser induction hybrid rapid cladding[J].Materials Science and Engineering A,2008,480:564-572.
【5】GOMEZ-DEL R T,GARRIDO M A,FERNANDEZ J E,et al.Influence of the deposition techniques on the mechanical properties and microstructure of NiCrBSi coatings[J].Journal of Materials Processing Technology,2008,204:304-312.
【6】WU X L.Micro-structural features of an iron-based laser coating[J].J Mater,1999,34(10):3355-3361.
【7】刘要武.Ni-Cr-B-Si激光熔覆层与H62黄铜基材间显微组织及微区分析[J].光学精密工程,2000,8(1):26-28.
【8】孙宜华,李晨辉,熊惟皓,等.铁基高铬合金激光熔覆层和堆焊层的组织性能对比[J].机械工程材料,2008,32(1):59-62.
【9】王新林,石世宏,郑启光.核阀密封面激光熔覆稀释控制研究[J].光电子·激光,2003,14(2):187-190.
【10】关振中.激光加工工艺手册[M].北京:中国计量出版社,1998.
【11】张增志.高效快速感应熔涂技术[M].北京:冶金工业出版社,2001.
【12】GONZALEZ R,CADENAS M,FERNANDEZ R.Wear behavior of flame sprayed NiCrBSi coating remelted by flame or by laser[J].Wear,2007,262:301-307.
【13】林凡,张少宗,施瑞鹤.高铬镍不锈钢的腐蚀电化学特性[J].材料保护,2003,33(3):50-52.
【14】颜永根,李明喜,张世宏,等.纳米CeO2对Ni基合金激光熔覆层的组织及耐蚀性的影响[J].中国稀土学报,2007,25(5):620-624.
【15】刘秀晨,安成强.金属腐蚀学[M].北京:国防工业出版社,1998.
【2】SUN R L,YANG D Z,GUO L X,et al.Microstructure and wear resistance of NiCrBSi laser clad layer on titanium alloy substrate[J].Surface and Coatings Technology,2000,132(2/3):251-255.
【3】李明喜,何宜柱,孙国雄.Ni基合金/45钢宽、窄带熔覆Co基合金的组织[J].中国激光,2003,30(11):1044-1048.
【4】ZHOU Sheng-feng,HUANG Yong-jun,ZENG Xiao-yan.Microstructure characteristics of Ni-based WC composite coatings by laser induction hybrid rapid cladding[J].Materials Science and Engineering A,2008,480:564-572.
【5】GOMEZ-DEL R T,GARRIDO M A,FERNANDEZ J E,et al.Influence of the deposition techniques on the mechanical properties and microstructure of NiCrBSi coatings[J].Journal of Materials Processing Technology,2008,204:304-312.
【6】WU X L.Micro-structural features of an iron-based laser coating[J].J Mater,1999,34(10):3355-3361.
【7】刘要武.Ni-Cr-B-Si激光熔覆层与H62黄铜基材间显微组织及微区分析[J].光学精密工程,2000,8(1):26-28.
【8】孙宜华,李晨辉,熊惟皓,等.铁基高铬合金激光熔覆层和堆焊层的组织性能对比[J].机械工程材料,2008,32(1):59-62.
【9】王新林,石世宏,郑启光.核阀密封面激光熔覆稀释控制研究[J].光电子·激光,2003,14(2):187-190.
【10】关振中.激光加工工艺手册[M].北京:中国计量出版社,1998.
【11】张增志.高效快速感应熔涂技术[M].北京:冶金工业出版社,2001.
【12】GONZALEZ R,CADENAS M,FERNANDEZ R.Wear behavior of flame sprayed NiCrBSi coating remelted by flame or by laser[J].Wear,2007,262:301-307.
【13】林凡,张少宗,施瑞鹤.高铬镍不锈钢的腐蚀电化学特性[J].材料保护,2003,33(3):50-52.
【14】颜永根,李明喜,张世宏,等.纳米CeO2对Ni基合金激光熔覆层的组织及耐蚀性的影响[J].中国稀土学报,2007,25(5):620-624.
【15】刘秀晨,安成强.金属腐蚀学[M].北京:国防工业出版社,1998.
相关信息