Design of High Strength Bolts Scanning Testing Imaging System Based on the Eddy Current Array Probe
摘 要
高强度螺栓是汽车、钢结构等的重要紧固件, 其质量直接关系到汽车、钢结构的安全性和可靠性。提出一种基于涡流传感器阵列的扫描成像检测系统, 用于检测高强度螺栓头杆结合部裂纹。与传统的机械旋转螺栓涡流检测系统相比, 该系统能快速检测出周向裂纹, 单次扫查覆盖的检测区域更大, 大大减小了机械结构的复杂性, 降低了误检率。提出的被检区域实时扫描检测图像系统, 也为其它大批量零部件裂纹检测提供了一种有效的解决途径。
Abstract
High strength bolt is the important fastener of automobile and steel structure and its quality directly affects the safety and reliability of the automobile and steel structure. After treatment process such as quenching and tempering, cracks occur in bolt. In the process of installation and using, bolt undertakes complicated stress. So the cracks (especially cracks in bolt root) will finally cause failure and fracture of bolt , which have serious consequence in use. A bolts scanning testing imaging system based on the eddy current array probe was introduced, which specializes in high strength bolt root crack detection. The system could effectively detect the cracks in bolt root so as to prevent the accidents happen. Compared to traditional mechanical rotary bolt eddy current testing system, this system could detect the circumferential crack quickly in lower mistaken rate, and with larger scan coverage, the system has simpler mechanical device. Using real time scanning testing imaging system is also a good solution to mass parts detection.
中图分类号 TG115.28
所属栏目 仪器方法
基金项目
收稿日期 2008/7/18
修改稿日期
网络出版日期
作者单位点击查看
备注楼敏珠(1962-), 女, 高级工程师, 硕士生导师, 主要从事电磁无损检测技术研究和设备开发。
引用该论文: LOU Min-Zhu,GUO Yun. Design of High Strength Bolts Scanning Testing Imaging System Based on the Eddy Current Array Probe[J]. Nondestructive Testing, 2009, 31(6): 485~487
楼敏珠,郭韵. 基于涡流阵列传感器的高强度螺栓扫描检测成像系统设计[J]. 无损检测, 2009, 31(6): 485~487
被引情况:
【1】杜金强,何宇廷,丁华, "基于涡流阵列的裂纹检测仿真分析",无损检测 33, 21-24(2011)
【2】杜金强,施越红,何宇廷, "裂纹长度和提离距离对涡流阵列传感器输出特性的影响",无损检测 37, 36-39(2015)
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】林俊明, 李同滨.相控阵涡流传感器的研制及其应用[J].无损检测, 2002, 24(2): 9-11.
【2】美国无损检测学会, 编.美国无损检测手册·电磁卷[M].中国机械工程学会无损检测分会, 译.上海: 世界图书出版公司, 1999.
【3】高印寒.一种高速多通道涡流信号采集系统的设计与实现[J].无损检测2003, 25(1): 21-24.
【4】吴迪, 吴超, 李春元.通用扫描成像检测软件的开发与应用[J].无损检测, 2003, 25(8): 403-406.
【5】刘君华.基于Labview的虚拟仪器设计[M].北京: 电子工业出版社, 2003.
【6】杨乐平, 李海涛.Labview程序设计与应用[M].北京: 电子工业出版社, 2001.
【2】美国无损检测学会, 编.美国无损检测手册·电磁卷[M].中国机械工程学会无损检测分会, 译.上海: 世界图书出版公司, 1999.
【3】高印寒.一种高速多通道涡流信号采集系统的设计与实现[J].无损检测2003, 25(1): 21-24.
【4】吴迪, 吴超, 李春元.通用扫描成像检测软件的开发与应用[J].无损检测, 2003, 25(8): 403-406.
【5】刘君华.基于Labview的虚拟仪器设计[M].北京: 电子工业出版社, 2003.
【6】杨乐平, 李海涛.Labview程序设计与应用[M].北京: 电子工业出版社, 2001.
相关信息