Fracture Analysis on High Strength Screws for Elevator
摘 要
某电梯用高强度螺钉在安装2个月后出现批量断裂现象,利用直读光谱仪、氮氢氧联合测定仪、光学显微镜、扫描电子显微镜等对螺钉断裂原因进行了分析。结果表明:该批螺钉由于镀锌后除氢不及时导致其本身氢含量较高和螺钉冷拔后未进行车削导致其在镀锌前表面就已存在大量的微小缺陷是导致该批螺钉安装后发生断裂的两个主要原因;这些微小缺陷充当了氢陷阱并造成应力集中,在螺钉所受的静拉应力作用下,氢在缺陷处不断富集,最终导致螺钉发生氢致延迟脆性断裂。
Abstract
A batch of high strength screws used in elevator fractured after assembling for two months, and the fracture reason was analyzed by using photoelectric direct reading spectrometer, N, H, O joint tester, optical microscopy and scanning election microscopy. The results show that not in time dehydrogenation after galvanization resulted in the high hydrogen content in the screws, and no turning process after cold drawing which resulted in the formation of a large number of small defects on the surface of the screws before galvanization. They were the two main reasons for the fracture of this batch of high strength screws. These small defects acted as hydrogen traps and caused stress concentration. With the enrichment of hydrogen in the defects and under the load of static pulling stress, the high strength screws happened hydrogen-induced delayed e-brittle fracture finally.
中图分类号 TH131.3
所属栏目 质量控制与失效分析
基金项目 上海市自然科学基金资助项目(09ZR1409900)
收稿日期 2010/2/26
修改稿日期
网络出版日期
作者单位点击查看
备注王 荣(1966-),男,教授级高级工程师。
引用该论文: WAND Rong,GUO Chun-qiu. Fracture Analysis on High Strength Screws for Elevator[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2010, 46(6): 392~395
王 荣,郭春秋. 电梯用高强度螺钉断裂分析[J]. 理化检验-物理分册, 2010, 46(6): 392~395
被引情况:
【1】郭春秋,王荣,李光福, "GCr15钢磨削开裂的特征及影响因素",机械工程材料 38, 90-94(2014)
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】GB/T 3098.1-2000 紧固件机械性能 螺栓、螺钉和螺柱[S].
【2】GB/T 10561-2005 钢中非金属夹杂物含量的测定 标准评级图显微检验方法[S].
【3】沈玲. 钢制螺栓镀锌后脆性断裂分析[J]. 航空制造技术, 2006(3):103-104.
【4】田野,王毛球, 李金许,等. 1 500 MPa级40CrNi3MoV钢的氢脆敏感性[J]. 金属学报, 2004, 44(4):403-408.
【5】吴连生. 失效分析技术[M]. 成都:四川科技出版社, 1985:246-250.
【6】王荣,孙明正. 高强度螺栓断裂失效分析[J]. 理化检验-物理分册,2008, 26(2):50-54.
【7】杨力,李晋, 孙浩,等. 超高强度螺栓断裂失效分析[J]. 理化检验-物理分册,2004, 40(4):195-198.
【2】GB/T 10561-2005 钢中非金属夹杂物含量的测定 标准评级图显微检验方法[S].
【3】沈玲. 钢制螺栓镀锌后脆性断裂分析[J]. 航空制造技术, 2006(3):103-104.
【4】田野,王毛球, 李金许,等. 1 500 MPa级40CrNi3MoV钢的氢脆敏感性[J]. 金属学报, 2004, 44(4):403-408.
【5】吴连生. 失效分析技术[M]. 成都:四川科技出版社, 1985:246-250.
【6】王荣,孙明正. 高强度螺栓断裂失效分析[J]. 理化检验-物理分册,2008, 26(2):50-54.
【7】杨力,李晋, 孙浩,等. 超高强度螺栓断裂失效分析[J]. 理化检验-物理分册,2004, 40(4):195-198.
相关信息