Microstructures and Mechanical Properties of Welded Joints for 1.4003 Ferritic Stainless Steel and Q235-C Steel
摘 要
采用室温拉伸、不同温度冲击、硬度及金相检验等分析方法对用熔化极混合气体保护焊焊接的1.4003铁素体不锈钢与Q235-C钢焊接接头的显微组织和性能进行了研究。试验结果表明:该焊接接头的抗拉强度与母材相当,焊缝的冲击性能略低于母材,1.4003铁素体不锈钢的热影响区(HAZ)冲击性能较差,焊缝为奥氏体+铁素体双相组织;Q235-C钢的熔合区出现明显界限,1.4003铁素体不锈钢焊接热影响区为晶粒粗大的单一铁素体组织。
Abstract
Microstructures and properties of welded joints for 1.4003 ferritic stainless steel and Q235-C steel by MAG were investigated by neams of room-temperature tensile test,variant temperature impact test ,hardness test and metallographic analyse. The results showed that the joints had good tensile strength which was no less than base metal. The impact properties of welded joints was little under base metal. HAZ on 1.4003 ferritic stainless steel side had bad impact properties. The microstructure of the welded seam was ferritie and austenitie duplex organize. HAZ on Q235-C steel side existed obvious interface between perlite and austenitie organize.But carbon diffusion phenomenon was not evident. HAZ on 1.4003 ferritic stainless steel side had unity coarsening ferritic grain.
中图分类号 TG407
所属栏目 试验与研究
基金项目
收稿日期 2008/7/16
修改稿日期
网络出版日期
作者单位点击查看
备注赵雯雯(1983-),女,硕士研究生。
引用该论文: ZHAO Wen-wen,XU Hong-ji,JIN Guang. Microstructures and Mechanical Properties of Welded Joints for 1.4003 Ferritic Stainless Steel and Q235-C Steel[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2009, 45(6): 335~338
赵雯雯,许鸿吉,金光. 1.4003铁素体不锈钢与Q235-C钢焊接接头的组织和力学性能[J]. 理化检验-物理分册, 2009, 45(6): 335~338
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】张孝福. 3Cr12——一种使用前景广阔的低铬铁素体不锈钢[J]. 不锈钢. 2004(2):9-11.
【2】《机械工程标准手册》编委会. 机械工程标准手册:焊接与切割卷[M]. 北京:中国标准出版社,2001.
【3】束德林.金属力学性能[M]. 北京:机械工业出版社,1999.
【4】林昭淑.金属学及热处理试验[M]. 长沙:湖南大学出版社,1986.
【5】埃里希·福克哈德,著.不锈钢焊接冶金[M]. 粟卓新,朱学军,译.北京:化学工业出版社,2004.
【6】何康生,曹雄夫. 异种金属焊接[M]. 北京:机械工业出版社,1986.
【2】《机械工程标准手册》编委会. 机械工程标准手册:焊接与切割卷[M]. 北京:中国标准出版社,2001.
【3】束德林.金属力学性能[M]. 北京:机械工业出版社,1999.
【4】林昭淑.金属学及热处理试验[M]. 长沙:湖南大学出版社,1986.
【5】埃里希·福克哈德,著.不锈钢焊接冶金[M]. 粟卓新,朱学军,译.北京:化学工业出版社,2004.
【6】何康生,曹雄夫. 异种金属焊接[M]. 北京:机械工业出版社,1986.
相关信息