AN ANALYSIS ON THE PROPERTIES AND MICROSTRUCTURE OF WELDING JOINT OF Ti17 ALLOY ELECTRON BEAM
摘 要
分析了Ti17合金真空电子束焊接接头的显微组织结构及其显微硬度分布规律,并结合室温和高温拉伸试验结果分析了焊接接头的力学性能。结果表明,用电子束焊接方法焊接的Ti17合金其焊缝区和热影响区显微组织为β相基体上分布着细长针状α相,母材为典型的α+β双相网篮组织,焊后焊缝晶粒细化,焊接接头的焊缝区硬度最高,焊缝的抗拉强度和缺口敏感性均高于母材。
Abstract
This paper adopts the electron beam weld (EBW) to weld Ti17 alloy, and makes testing on the mechanical properties of its weldments by means of tension testing at room temperature and 400℃, then analyses the microstructure of Ti17 alloy EB weldments by optical micrographs. It is found that tensile strength is not lower but higher than those of base metal. The Ti17 alloy welding joint have a thicker skin than its matrix on gap. The hardness of weld metal and HAZ are also higher than that of base metal. The microstructure of base metal and HAZ is like network made up of α+β. The microstructure of weld metal is threadlike α on the base of β, and the grains have grown thinner. All these prove that ideal welded joint of Ti17 alloy can be acquired by the way of EBW.
中图分类号 TG113.14
所属栏目
基金项目
收稿日期 2005/10/28
修改稿日期
网络出版日期
作者单位点击查看
备注杨磊(1980-),男,硕士研究生。
引用该论文: YANG Lei,ZHAO Xiu-juan,XU Hong-ji. AN ANALYSIS ON THE PROPERTIES AND MICROSTRUCTURE OF WELDING JOINT OF Ti17 ALLOY ELECTRON BEAM[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2006, 42(10): 498~501
杨磊,赵秀娟,许鸿吉. Ti17合金电子束焊接接头的性能及组织分析[J]. 理化检验-物理分册, 2006, 42(10): 498~501
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】Wood, Favor[美]主编.钛合金手册[M].重庆:科学技术出版社, 1983.
【2】胡礼木.钛合金TI-6Al-4V电子束焊接接头的性能研究[J].陕西工学院学报, 1997,13(4):45-49.
【3】吴会强,冯吉才,何景山,等.电子束焊接Ti-6Al-4V接头断裂行为机制[J].焊接学报, 2004,17(8):93-96.
【4】王焕琴.钛及钛合金焊接接头的组织、性能和断裂特性[J].焊接学报, 2001,8(11):17-20.
【5】戚运莲,洪 权,刘向,等.Ti工业进展[J].稀有金属材料和工程, 2004,7(11):28-30.
【6】中国机械工程学会,焊接学会.焊接金相图谱[M].北京:机械工业出版社, 1987.
【7】E A 鲍利索娃[苏]等著,陈石卿译.钛合金金相学[M].北京:国防工业出版社, 1986.
【2】胡礼木.钛合金TI-6Al-4V电子束焊接接头的性能研究[J].陕西工学院学报, 1997,13(4):45-49.
【3】吴会强,冯吉才,何景山,等.电子束焊接Ti-6Al-4V接头断裂行为机制[J].焊接学报, 2004,17(8):93-96.
【4】王焕琴.钛及钛合金焊接接头的组织、性能和断裂特性[J].焊接学报, 2001,8(11):17-20.
【5】戚运莲,洪 权,刘向,等.Ti工业进展[J].稀有金属材料和工程, 2004,7(11):28-30.
【6】中国机械工程学会,焊接学会.焊接金相图谱[M].北京:机械工业出版社, 1987.
【7】E A 鲍利索娃[苏]等著,陈石卿译.钛合金金相学[M].北京:国防工业出版社, 1986.
相关信息