Cause Analysis on Corrosion of 316L Stainless Steel Bolts of Seawater Pump Impeller
摘 要
针对海水泵叶轮316L不锈钢螺钉的腐蚀现象,综合运用宏观检验、金相检验、化学成分分析、扫描电镜与能谱分析,以及动电位极化分析方法对螺钉的腐蚀原因进行了分析。结果表明: 腐蚀螺钉的化学成分不符合316L不锈钢的标准要求,且高脉冲电流电火花加工的变质层中存在微裂纹,该变质层的局部残留进一步降低了螺钉的耐蚀性,最后对提高螺钉耐蚀性提出了相应建议。
Abstract
Aiming to the corrosion phenomenon of 316L stainless steel bolt of seawater pump impeller, the cause of bolts corrosion was analyzed through macroscopic and metallographic inspection, chemical composition analysis, scanning electron microscopy and energy spectrum analysis, and potentiodynamic polarization analysis. The results show that the chemical composition of the corroded bolts didn’t meet the standard requirement, and microcracks existed in the metamorphic layer after sparkle drilling under high pulse current. The existence of residual metamorphic layer further degraded the corrosion resistance. Finally the corresponding suggestion was recommended to enhance the bolts corrosion resistance.
中图分类号 TG142.1+5 TG178 DOI 10.11973/lhjy-wl201511014
所属栏目 质量控制与失效分析
基金项目 国家自然科学基金资助项目 (51171051,51101024,51171037) ;国家自然科学基金委-神华集团“煤炭联合基金”资助项目(51134013)
收稿日期 2015/1/21
修改稿日期
网络出版日期
作者单位点击查看
备注关 锰(1975-),男,高级工程师。
引用该论文: GUAN Meng,WANG Dong-ying,CHENG Cong-qian,LI Qian,ZHAO Jie. Cause Analysis on Corrosion of 316L Stainless Steel Bolts of Seawater Pump Impeller[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2015, 51(11): 806~809
关锰,王冬颖,程从前,李倩,赵杰. 海水泵叶轮316L不锈钢螺钉的腐蚀原因分析[J]. 理化检验-物理分册, 2015, 51(11): 806~809
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】邹龙江,周全,丛丹妮,等. 316L不锈钢泵轴断裂原因分析[J]. 理化检验-物理分册, 2014, 50(5):356-358.
【2】ASTM G46.2387-2005Standard guide for examination and evaluation of pitting corrosion[S].
【3】GB/T 1220-2007不锈钢棒[S].
【4】孙德跃. 电火花加工螺纹[J].装备机械,2005(2):52-55.
【5】郑良贵,陈子熙. 电火花加工表面变质层机械性能的研究[J]. 电加工与磨具,1994(2):24-29.
【6】张恒,叶文荣,孙斌,等. HDR双相不锈钢海水管路的腐蚀与预防[J]. 腐蚀与防护,2013, 3(1):45-48.
【7】王健,程从前,赵杰,等. 316L/2205与1Cr17Ni2/2205不锈钢电偶对在3.5%NaCl溶液中的腐蚀[J]. 材料保护, 2014, 47(12):27-29.
【2】ASTM G46.2387-2005Standard guide for examination and evaluation of pitting corrosion[S].
【3】GB/T 1220-2007不锈钢棒[S].
【4】孙德跃. 电火花加工螺纹[J].装备机械,2005(2):52-55.
【5】郑良贵,陈子熙. 电火花加工表面变质层机械性能的研究[J]. 电加工与磨具,1994(2):24-29.
【6】张恒,叶文荣,孙斌,等. HDR双相不锈钢海水管路的腐蚀与预防[J]. 腐蚀与防护,2013, 3(1):45-48.
【7】王健,程从前,赵杰,等. 316L/2205与1Cr17Ni2/2205不锈钢电偶对在3.5%NaCl溶液中的腐蚀[J]. 材料保护, 2014, 47(12):27-29.
相关信息