Causes Analysis on Cracking of 2A14 Aluminium Alloy Container
摘 要
采用化学成分分析、拉伸性能测试和显微组织分析等方法, 对2A14铝合金容器罐开裂的原因进行了分析。结果表明: 2A14铝合金焊接接头熔合线附近存在的氢气孔是导致铝制容器罐开裂的主要原因。气孔的存在降低了接头的致密性及有效承载面积, 使接头抵抗变形能力下降, 最终造成容器罐开裂失效。
Abstract
By means of chemical composition analysis, tensile property test, microstructure analysis and so on, the cracking causes of 2A14 aluminium alloy container were analyzed. The results show that the main reason for cracking of the 2A14 aluminium alloy container was the hydrogen holes near the fusion line of the welding joints. The welding hydrogen holes reduced the compactness and effective bearing area of the welding joints. The capacity of deformation resistance of the joints was weakened, and eventually it resulted in the cracking and failure of the container.
中图分类号 TG115.2 DOI 10.11973/lhjy-wl201603018
所属栏目
基金项目
收稿日期 2015/4/21
修改稿日期
网络出版日期
作者单位点击查看
备注李金梅(1986-),女,硕士研究生。
引用该论文: LI Jin-mei,SHI Wei,WANG Shun-hua,YANG Li. Causes Analysis on Cracking of 2A14 Aluminium Alloy Container[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2016, 52(3): 217~219
李金梅,史伟,王顺花,杨莉. 2A14铝合金容器罐开裂原因分析[J]. 理化检验-物理分册, 2016, 52(3): 217~219
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】王亚荣,滕文华.电子束焊接2A14铝合金接头的组织与特征[J].中国有色金属学报,2012,22(12): 3307-3311.
【2】薛小怀,邓正才.6061铝合金气孔敏感性研究[C]//汽车焊接国际论坛论文集.北京: 机械工业出版社, 2003.
【3】刘春燕,周丹晨.热处理工艺对2A14锻件组织和性能影响[J].热加工工艺, 2009,38(24): 148-150.
【4】韩德成,陈东方.A5083铝合金焊接气孔敏感性研究[J].机车车辆工艺,2014,4(2): 4-8.
【5】康举,李艳军.两种TIG焊工艺对LD10接头力学性能的影响[J].焊接学报, 2014,35(3): 109-112.
【6】王亚荣,黄文荣.焊后热处理对2A14高强铝合金电子束焊接头组织及力学性能的影响[J].机械工程学报, 2011,47(20): 141-145.
【7】王亚荣,黄文荣.2A14高强铝合金电子束焊接头缺陷分析[J].焊接学报, 2013,34(3): 109-112.
【2】薛小怀,邓正才.6061铝合金气孔敏感性研究[C]//汽车焊接国际论坛论文集.北京: 机械工业出版社, 2003.
【3】刘春燕,周丹晨.热处理工艺对2A14锻件组织和性能影响[J].热加工工艺, 2009,38(24): 148-150.
【4】韩德成,陈东方.A5083铝合金焊接气孔敏感性研究[J].机车车辆工艺,2014,4(2): 4-8.
【5】康举,李艳军.两种TIG焊工艺对LD10接头力学性能的影响[J].焊接学报, 2014,35(3): 109-112.
【6】王亚荣,黄文荣.焊后热处理对2A14高强铝合金电子束焊接头组织及力学性能的影响[J].机械工程学报, 2011,47(20): 141-145.
【7】王亚荣,黄文荣.2A14高强铝合金电子束焊接头缺陷分析[J].焊接学报, 2013,34(3): 109-112.
相关信息