Numerical Simulation for Welding Sequence Optimization of Gymnastic Bicycle Frame
摘 要
利用MARC软件, 采用壳单元替代实体单元建立了健身自行车架的焊接有限元模型, 分析了壳单元替代实体单元模拟的误差并得到了修正系数,为1.136 7; 对车架的五道焊缝在两种焊接方案、十二种焊接顺序下进行了焊接模拟, 分析了车架的主要焊接变形,对焊接顺序进行了优化并进行了试验验证。结果表明: 车架的焊接变形主要表现为座垫套管的偏转变形; 采用非连续焊接方案, 不同焊接顺序下座垫套管的偏转变形量均小于连续焊接方案下的; 最佳焊接顺序为前斜管与套管环焊缝、前斜管与定位板内侧焊缝、套管与定位板外侧焊缝、套管与定位板内侧焊缝、前斜管与定位板外侧焊缝的依次非连续焊接; 不同顺序非连续焊接后座垫套管的偏转变形模拟值与实测值较吻合, 证明了有限元模型的准确性。
Abstract
The welding finite element model of the gymnastic bicycle frame was built using shell elements instead of solid elements by software MARC. The errors between the simulation by shell elements and by solid elements were analyzed and the correct coefficient of 1.136 7 was obtained. The welding simulation by two welding schemes in twelve sequences of the five welds of the frame was conducted. The main welding deformation of the frame was analyzed, the welding sequence was optimized and verified by experiments. The results show that the deflection of the cushion tube was the main welding deformation of the frame. The deflections of the cushion tube after discontinuous welding in different sequences were lower than those after continuous welding. The optimal welding sequence was discontinuous welding in the order of the girth weld of anterior inclined tube and cushion tube, inner side weld of anterior inclined tube and locating plate, lateral weld of cushion tube and locating plate, inner side weld of cushion tube and locating plate, lateral weld of anterior inclined tube and locating plate. The simulated deflection values of the cushion tube after discontinuous welding in different sequences coincided well with the measured results, proving the accuracy of the finite element model.
中图分类号 TG404 DOI 10.11973/jxgccl201604010
所属栏目 物理模拟与数值模拟
基金项目 福建省科技平台项目(2013H2003); 中央高校基本科研业务费资助项目(JB-ZR1211)
收稿日期 2015/12/4
修改稿日期 2016/3/13
网络出版日期
作者单位点击查看
备注张华(1991-), 男, 甘肃嘉峪关人, 硕士研究生。
引用该论文: ZHANG Hua,ZHOU Guang-tao,WANG Fei. Numerical Simulation for Welding Sequence Optimization of Gymnastic Bicycle Frame[J]. Materials for mechancial engineering, 2016, 40(4): 38~42
张华,周广涛,王霏. 健身自行车架焊接顺序优化的数值模拟[J]. 机械工程材料, 2016, 40(4): 38~42
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】田锡唐.焊接结构[M].北京: 机械工业出版社,1982.
【2】武奇,邱惠清.基于壳单元的焊接接头的结构应力求解[J].焊接学报,2010,31(7): 22-26.
【3】周广涛,刘雪松,闫德俊,等.顶板焊接顺序优化减小焊接变形的预测[J].焊接学报,2009,30(9): 109-112.
【4】薛忠明,曲文卿,柴鹏,等.焊接变形预测技术研究进展[J].焊接学报,2003,24(3): 87-90.
【5】廖娟,凌泽民,张永龙.考虑相变的高强钢T型接头焊接残余应力和变形的数值模拟[J].机械工程材料,2013,37(8): 85-88,101.
【6】李灿,傅定发,王冠,等.焊接顺序对6061-T6铝合金矩形焊缝焊接残余应力及变形量的影响[J].机械工程材料,2012,36(7): 88-92.
【7】陆明炯.实用机械工程材料手册[M].沈阳: 辽宁科学技术出版社,2004: 3-6.
【8】GOLDAK J,CHAKRAVARTI A,BIBBY M.A new finite element model for welding heat sources[J].Metallurgua Transactions B,1984,15(2): 299-305.
【9】方洪渊.焊接结构学[M].北京: 机械工业出版社,2008: 7-15.
【10】黄海瀚,周广涛.装载机后车架焊接顺序优化的数值仿真[J].计算机辅助工程,2014,24(3): 30-34,59.
【2】武奇,邱惠清.基于壳单元的焊接接头的结构应力求解[J].焊接学报,2010,31(7): 22-26.
【3】周广涛,刘雪松,闫德俊,等.顶板焊接顺序优化减小焊接变形的预测[J].焊接学报,2009,30(9): 109-112.
【4】薛忠明,曲文卿,柴鹏,等.焊接变形预测技术研究进展[J].焊接学报,2003,24(3): 87-90.
【5】廖娟,凌泽民,张永龙.考虑相变的高强钢T型接头焊接残余应力和变形的数值模拟[J].机械工程材料,2013,37(8): 85-88,101.
【6】李灿,傅定发,王冠,等.焊接顺序对6061-T6铝合金矩形焊缝焊接残余应力及变形量的影响[J].机械工程材料,2012,36(7): 88-92.
【7】陆明炯.实用机械工程材料手册[M].沈阳: 辽宁科学技术出版社,2004: 3-6.
【8】GOLDAK J,CHAKRAVARTI A,BIBBY M.A new finite element model for welding heat sources[J].Metallurgua Transactions B,1984,15(2): 299-305.
【9】方洪渊.焊接结构学[M].北京: 机械工业出版社,2008: 7-15.
【10】黄海瀚,周广涛.装载机后车架焊接顺序优化的数值仿真[J].计算机辅助工程,2014,24(3): 30-34,59.
相关信息