Corrosion Reasons of the Plate Heat Exchanger of ASTM SMO 254 Stainless Steel
摘 要
某炼厂常压塔顶全焊接板式换热器(材质ASTM SMO254),在使用约半年时间即出现大面积腐蚀穿孔。从现场情况看,换热器常顶油气侧入口焊接面结垢严重,出现大面积铵盐沉积,清洗后发现,垢下发生严重腐蚀,甚至穿孔。本工作从工艺防腐蚀和换热器内部结构等方面对腐蚀原因进行了分析。结果表明:由于注水量的不足,导致铵盐在换热板表面结垢,同时“一脱三注”的不稳定,导致了严重的垢下腐蚀。
Abstract
Perforation corrosion occurred in the tube sheet of plate heat exchanger in an atmosphere overhead condenser after service for half a year. The material of the tube sheet is ASTM SMO254. Severe scaling occurred on the surface of the plate of the heat exchanger and some ammonium salt was deposited. Severe corrosion, even perforation, was observed after cleaning the scale. The failure reason was analyzed in the view of the anti-corrosion technology and the constructure of the heat exchanger. The results show that the lacking of the water injection generated the deposition of the ammonium salt and the corrosion happened under the deposit, the instability of the technology also had some influence on the corrosion.
中图分类号 TE624 DOI 10.11973/fsyfh-201611017
所属栏目 失效分析
基金项目
收稿日期 2015/5/18
修改稿日期
网络出版日期
作者单位点击查看
备注刘志平(1985-),工程师,学士,从事石油化工企业腐蚀防护研究,
引用该论文: LIU Zhi-ping,WANG Li,ZHANG Wei. Corrosion Reasons of the Plate Heat Exchanger of ASTM SMO 254 Stainless Steel[J]. Corrosion & Protection, 2016, 37(11): 932
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】董其伍,刘敏珊,苏立建. 管壳式换热器研究进展[J]. 化工设备与管道,2006,43(6):18-22.
【2】程宝华,李先瑞. 板式换热器及换热装置技术应用手册[M]. 北京:中国建设工业出版社,2005:1-57,90-246.
【3】吉田敬堂,计范. 板式换热器的最新动向[J]. 化工装备技术,2013(6):13-23.
【4】任书恒. 板式换热器的应用及其发展前景[J]. 石油化工设备技术,2011,12(1):7-11.
【5】何光文. 板式换热器结构参数优化及其传热性能研究[D]. 广州:华南理工大学,2012:45-46.
【6】杨德钧,沈卓身. 金属腐蚀学[M]. 北京:冶金工业出版社,2003:122-162.
【7】杨崇麟. 板式换热器工程设计手册[M]. 北京:机械工程出版社,2004:32-35.
【8】SOUTO R M,GONZALEZ-GARCIA Y,GONZALEZ S. Application to the investigation of degradation processes at defective coated metals[J]. Corrosion Science,2005,47(12):3312-3323.
【9】FRANKEL G S. Pitting corrosion of metal[J]. J Electrochem Soc,2008,145(6):2186-2198.
【10】张铁柱. 板式换热器应用中存在的问题及对策[J]. 中国高新技术企业,2008(21):117-125.
【2】程宝华,李先瑞. 板式换热器及换热装置技术应用手册[M]. 北京:中国建设工业出版社,2005:1-57,90-246.
【3】吉田敬堂,计范. 板式换热器的最新动向[J]. 化工装备技术,2013(6):13-23.
【4】任书恒. 板式换热器的应用及其发展前景[J]. 石油化工设备技术,2011,12(1):7-11.
【5】何光文. 板式换热器结构参数优化及其传热性能研究[D]. 广州:华南理工大学,2012:45-46.
【6】杨德钧,沈卓身. 金属腐蚀学[M]. 北京:冶金工业出版社,2003:122-162.
【7】杨崇麟. 板式换热器工程设计手册[M]. 北京:机械工程出版社,2004:32-35.
【8】SOUTO R M,GONZALEZ-GARCIA Y,GONZALEZ S. Application to the investigation of degradation processes at defective coated metals[J]. Corrosion Science,2005,47(12):3312-3323.
【9】FRANKEL G S. Pitting corrosion of metal[J]. J Electrochem Soc,2008,145(6):2186-2198.
【10】张铁柱. 板式换热器应用中存在的问题及对策[J]. 中国高新技术企业,2008(21):117-125.
相关信息