Effect of Hot Isostatic Pressing and Annealing on Microstructure and Tensile Property of Cast TG6 Titanium Alloy
摘 要
对熔模精密铸造的近α型TG6钛合金依次进行了热等静压和不同温度退火处理,研究了不同状态合金的显微组织和拉伸性能。结果表明:铸态合金的显微组织主要为魏氏组织,组织中存在缩松缺陷;其室温抗拉强度和伸长率分别为871.3 MPa,0.8%,缩松处为断裂源。900℃热等静压处理消除了缩松缺陷,合金的室温伸长率提高至3.7%,拉伸断口呈准解理断裂特征。经700~800℃退火处理后,合金组织中的β板条部分溶解并析出条状及颗粒状硅化物,在α板条中弥散分布着α2相析出物;其室温伸长率提高到11%以上,室温及550℃拉伸断口为韧性断裂和解理断裂共存的混合型断口,而650℃和700℃拉伸断口呈腐蚀开裂特征。
Abstract
The hot isostatic pressing and annealing treatment at different temperatures were successively conducted on a near-α TG6 titanium alloy by precision casting, and then the microstructure and tensile properties of the alloy in different states was studied. The results show that the microstructure of the cast alloy mainly consisted of Widmanstatten structure, and the shrinkage defect existed in the microstructure; the room temperature tensile strength reached 871.3 MPa, while the elongation was only 0.8%; the shrinkage defect became the crack initiation source. After hot isostatic pressing at 900℃, the shrinkage defect was eliminated, the room temperature elongation increased to 3.7%, and the tensile fracture showed features of quasi cleavage fracture. After annealing at temperatures of 700℃-800℃, β lath in the alloy microstructure was dissolved partially and band-like and granular silicide precipitated, meanwhile the α2 phase dispersively distributed in the α lath; the room temperature elongation was improved to over 11%, and the tensile fracture at room temperature and 550℃ showed a mixed fracture of cavitation and cleavage, while those at 650℃ and 700℃ showed characteristics of corrosion cracking.
中图分类号 TG146.2 DOI 10.11973/jxgccl201702023
所属栏目 材料性能及应用
基金项目 北京市科技计划项目(Z141104004414053)
收稿日期 2015/12/6
修改稿日期 2017/1/12
网络出版日期
作者单位点击查看
备注朱郎平(1985-),男,北京人,工程师,硕士。
引用该论文: ZHU Lang-ping,LI Jian-chong,MO Xiao-fei,WEI Zhan-lei,LI Yan,LUO Qian,NAN Hai. Effect of Hot Isostatic Pressing and Annealing on Microstructure and Tensile Property of Cast TG6 Titanium Alloy[J]. Materials for mechancial engineering, 2017, 41(2): 106~111
朱郎平,李建崇,莫晓飞,魏战雷,李岩,罗倩,南海. 热等静压及退火对铸造TG6钛合金组织和拉伸性能的影响[J]. 机械工程材料, 2017, 41(2): 106~111
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】王清江,刘建荣,杨锐.高温钛合金的现状与前景[J].航空材料学报,2014,34(4):1-26.
【2】曾立英,赵永庆,洪权,等.600℃高温钛合金的研发[J].钛工业进展,2012,29(5):1-5.
【3】陈玉勇,赵而团,孔凡涛,等.离心力场下熔模铸造600℃高温钛合金流动性研究[C]//中国有色金属工业协会钛锆铪分会2011年会论文集.北京:中国有色金属工业协会钛锆铪分会,2011:272-277.
【4】陈玉勇,肖树龙,孔凡涛.高温钛合金及TiAl金属间化合物的精密铸造技术及应用前景[J].金属学报,2002,38(增1):39-44.
【5】王涛,郭洪镇,赵张龙,等.TG6合金等温变形条件下组织演变与性能研究[J].稀有金属材料与工程,2010,39(10):1849-1852.
【6】蔡建民,张华,黄旭,等.600℃时钛合金高温低循环疲劳行为及其微观机理[J].中国有色金属学报,2010,20(s1):342-347.
【7】WANG T,GUO H Z,ZHANG Y Q.Effect of hot forging temperature on microstructure and mechanical property of TG6 high temperature titanium alloy[J].Acta Metallurgica Sinica,2010,46(8):913-920.
【8】LEYENS C,PETERS M.Titanium and titanium alloys[M].Weinheim, Germany:WILEY-VCH Verlag GmbH & Co., KGaA,2003:18-19.
【9】张钧,李东.高温钛合金中的α2相[M].沈阳:东北大学出版社,2002:36-37.
【10】张钧,李东.时效热处理对近α钛合金中α2相析出的影响[J].金属学报,2002,38(增1):214-216.
【11】李娟,蔡建民,段锐.近α型TG6高温钛合金中硅化物的沉淀析出行为[J].航空材料学报,2012,32(5):32-36.
【12】段锐,张华,蔡建民,等.显微组织对近α型TG6钛合金高温蠕变变形行为的影响[J].中国有色金属学报,2010,20(s1):11-15.
【13】段锐,蔡建民,李臻熙. 初生α相含量对近α钛合金TG6拉伸性能和热稳定性的影响[J].航空材料学报,2007,27(3):17-22.
【14】李娟,蔡建民,黄旭,等.TG6高温钛合金中α2相的沉淀析出行为及其对塑形的影响[J].航空材料学报,2011,31(增1):80-84.
【15】陶春虎,李庆瑔,刘昌奎,等.航空用钛合金的失效及其预防[M].北京:航空工业出版社,2002:89-92.
【2】曾立英,赵永庆,洪权,等.600℃高温钛合金的研发[J].钛工业进展,2012,29(5):1-5.
【3】陈玉勇,赵而团,孔凡涛,等.离心力场下熔模铸造600℃高温钛合金流动性研究[C]//中国有色金属工业协会钛锆铪分会2011年会论文集.北京:中国有色金属工业协会钛锆铪分会,2011:272-277.
【4】陈玉勇,肖树龙,孔凡涛.高温钛合金及TiAl金属间化合物的精密铸造技术及应用前景[J].金属学报,2002,38(增1):39-44.
【5】王涛,郭洪镇,赵张龙,等.TG6合金等温变形条件下组织演变与性能研究[J].稀有金属材料与工程,2010,39(10):1849-1852.
【6】蔡建民,张华,黄旭,等.600℃时钛合金高温低循环疲劳行为及其微观机理[J].中国有色金属学报,2010,20(s1):342-347.
【7】WANG T,GUO H Z,ZHANG Y Q.Effect of hot forging temperature on microstructure and mechanical property of TG6 high temperature titanium alloy[J].Acta Metallurgica Sinica,2010,46(8):913-920.
【8】LEYENS C,PETERS M.Titanium and titanium alloys[M].Weinheim, Germany:WILEY-VCH Verlag GmbH & Co., KGaA,2003:18-19.
【9】张钧,李东.高温钛合金中的α2相[M].沈阳:东北大学出版社,2002:36-37.
【10】张钧,李东.时效热处理对近α钛合金中α2相析出的影响[J].金属学报,2002,38(增1):214-216.
【11】李娟,蔡建民,段锐.近α型TG6高温钛合金中硅化物的沉淀析出行为[J].航空材料学报,2012,32(5):32-36.
【12】段锐,张华,蔡建民,等.显微组织对近α型TG6钛合金高温蠕变变形行为的影响[J].中国有色金属学报,2010,20(s1):11-15.
【13】段锐,蔡建民,李臻熙. 初生α相含量对近α钛合金TG6拉伸性能和热稳定性的影响[J].航空材料学报,2007,27(3):17-22.
【14】李娟,蔡建民,黄旭,等.TG6高温钛合金中α2相的沉淀析出行为及其对塑形的影响[J].航空材料学报,2011,31(增1):80-84.
【15】陶春虎,李庆瑔,刘昌奎,等.航空用钛合金的失效及其预防[M].北京:航空工业出版社,2002:89-92.
相关信息