Numerical Simulation on Stress Field of Cold Metal Transfer (CMT) Welded Joint Aluminum and Steel Dissimilar Metals
摘 要
利用ABAQUS有限元软件对铝-钢异种金属冷金属过渡(CMT)焊接过程中焊接接头应力分布进行了数值模拟,分析了应力分布的变化规律,并进行了试验验证。结果表明:不同焊接时间下,焊接接头在钢板和铝合金板侧的von Mises应力分布不对称,其中铝合金板侧承受的应力较钢板侧的小;在焊接过程中,近焊缝处的纵向应力由压应力转变为拉应力,横向应力在焊初始阶段为拉应力,随后变为压应力,再转变为拉应力;在铝合金板侧和钢板侧热影响区的纵向残余拉应力最大,分别为125,208 MPa,位于铝合金板侧和钢板侧的横向残余压应力峰值几乎相同,约为80 MPa;残余应力分布模拟结果与试验结果的拟合优度为0.75,证明了模拟结果的准确性。
Abstract
The numerical simulation of stress distribution in aluminum-steel dissimilar metal welded joint during cold metal transition (CMT) welding was carried out by using ABAQUS finite element software. The variation law of stress distribution was analyzed and verified by experiments. The results show that at different welding times, the von Mises stresses unsymmetrically distributed at steel plate side and Al alloy plate side in the welded joint. And the stresses at Al alloy plate side were smaller than those at steel plate side. During the welding process, the longitudinal stress near the weld changed from the compressive stress into tensile stress, while the lateral stress at the welding initiating stage was tensile stress, then changed into compressive stress and then tensile stress. The longitudinal residual tensile stresses reached the largest values in the heat affect zone near the side of steel plate and Al alloy plate, which were 125 MPa and 208 MPa, respectively, while the peak values of lateral residual compressive stress were almost the same at both sides, which was about 80 MPa. The goodness-of-fit between the simulated and test results of residue stress distribution was 0.75, indicating the accuracy of the simulation results.
中图分类号 TG409 DOI 10.11973/jxgccl201706020
所属栏目 物理模拟与数值模拟
基金项目 国家自然科学基金资助项目(51675255,51265028)
收稿日期 2017/3/13
修改稿日期 2017/5/10
网络出版日期
作者单位点击查看
备注刘国辉(1972-),男,辽宁朝阳人,高级工程师,博士
引用该论文: LIU Guohui,CHE Hongyan,MA Lei,YU Siliang,CAO Rui. Numerical Simulation on Stress Field of Cold Metal Transfer (CMT) Welded Joint Aluminum and Steel Dissimilar Metals[J]. Materials for mechancial engineering, 2017, 41(6): 90~94
刘国辉,车洪艳,马雷,余斯亮,曹睿. 铝-钢异种金属CMT焊接接头应力场的数值模拟[J]. 机械工程材料, 2017, 41(6): 90~94
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】秦国梁, 武传松. 铝合金/钢异种材料熔钎焊接工艺及其研究现状[J]. 机械工程学报, 2016, 52(24):24-35.
【2】JARRELL A W, STRAUSS A M, COOK G E. Dissimilar metal T-joint of aluminum and steel formed by friction stir extrusion[M]//Friction Stir Welding and Processing IX.[S.l.]:Springer International Publishing, 2017:91-96.
【3】郭斌, 张李超. Cold Metal Transfer(CMT)与CMT Advanced的异同研究[J]. 精密成形工程, 2016(2):50-54.
【4】张洪涛, 何鹏, 孔庆伟,等. 铝钢异种材料焊接研究现状与发展[J]. 焊接, 2006(12):7-12.
【5】HU J, TASI H L. Heat and mass transfer in gas metal arc welding. PartⅡ:The metal[J]. International Journal of Heat and Mass Transfer, 2007, 50(2):808-820.
【6】CHO J H, NA S J.Three-dimensional analysis of molten pool in GMA-laser hybrid welding[J]. Welding Journal, 2009, 80(1):35-43.
【7】张洪涛. 铝/镀锌钢板CMT熔-钎焊机理研究[D]. 哈尔滨:哈尔滨工业大学, 2008.
【8】曹睿, 余斯亮, 王岑,等. 铝钢异种金属CMT焊接温度场的数值模拟[J]. 兰州理工大学学报, 2013, 39(5):19-22.
【9】曹睿, 余刚, 陈剑虹. 铝合金和镀锌钢异种金属CMT焊接性分析[J]. 焊接, 2012(1):31-36.
【2】JARRELL A W, STRAUSS A M, COOK G E. Dissimilar metal T-joint of aluminum and steel formed by friction stir extrusion[M]//Friction Stir Welding and Processing IX.[S.l.]:Springer International Publishing, 2017:91-96.
【3】郭斌, 张李超. Cold Metal Transfer(CMT)与CMT Advanced的异同研究[J]. 精密成形工程, 2016(2):50-54.
【4】张洪涛, 何鹏, 孔庆伟,等. 铝钢异种材料焊接研究现状与发展[J]. 焊接, 2006(12):7-12.
【5】HU J, TASI H L. Heat and mass transfer in gas metal arc welding. PartⅡ:The metal[J]. International Journal of Heat and Mass Transfer, 2007, 50(2):808-820.
【6】CHO J H, NA S J.Three-dimensional analysis of molten pool in GMA-laser hybrid welding[J]. Welding Journal, 2009, 80(1):35-43.
【7】张洪涛. 铝/镀锌钢板CMT熔-钎焊机理研究[D]. 哈尔滨:哈尔滨工业大学, 2008.
【8】曹睿, 余斯亮, 王岑,等. 铝钢异种金属CMT焊接温度场的数值模拟[J]. 兰州理工大学学报, 2013, 39(5):19-22.
【9】曹睿, 余刚, 陈剑虹. 铝合金和镀锌钢异种金属CMT焊接性分析[J]. 焊接, 2012(1):31-36.
相关信息