Influence of Beam Welding Process on Intergranular Corrosion Resistance of 304 Stainless Steel Weld
摘 要
采用3种不同的电子束焊接工艺焊接304不锈钢,通过显微组织观察、XRD分析、极化曲线测试、动电位再活化(EPR)试验研究了不锈钢焊缝的抗晶间腐蚀性能。结果表明:减少焊接热输入量和添加熔入性焊丝这两种方法都能减少电子束焊缝中铬的碳化物的析出,降低焊缝的敏化度,提高焊缝的抗晶间腐蚀性能;与减少焊接热输入量相比,添加熔入性焊丝对晶间腐蚀的影响更大,焊缝抗晶间腐蚀性能提高更显著。
Abstract
304 stainless steel was welded by three different processes of electron beam welding.The intergranular corrosion resistance of the electron beam weld of 304 stainless steel was studied through microstructure observation,XRD analysis,polarization curve testing and electrokinetic potential reactivation (EPR) test.The results show that two methods,reducing the amount of heat input and adding fusing welding wire,can reduce the precipitation of chromium carbides in the electron beam weld,reduce the degree of sensitization and improve the intergranular corrosion resistance of the weld.Compared with reducing the amount of heat input,adding fusing welding wire had more influence on intergranular corrosion,and can more significantly improve the intergranular corrosion resistance of the weld.
中图分类号 TG172 DOI 10.11973/fsyfh-201708005
所属栏目 试验研究
基金项目 南通市产学研协同创新计划项目(BC2014010);上海市钢铁冶金新技术开发应用重点实验室开放课题基金资助(SELF-2015-01)
收稿日期 2016/5/12
修改稿日期
网络出版日期
作者单位点击查看
引用该论文: WANG Yongdong,ZHONG Qingdong,REN Shuaidong. Influence of Beam Welding Process on Intergranular Corrosion Resistance of 304 Stainless Steel Weld[J]. Corrosion & Protection, 2017, 38(8): 593
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】顾帅帅,钟庆东,蒋继波,等. 304不锈钢在RCC-M1310标准下的耐蚀性[J]. 腐蚀与防护,2015,36(5):480-483.
【2】张晶莹. 304奥氏体不锈钢晶间腐蚀的研究及防护[J]. 装备制造技术,2012(2):154-156.
【3】张春雷,陈亚庆. Super304H焊接接头晶间腐蚀性能的电化学动电位再活化法评价[J]. 广东电力,2015(3):1-4.
【4】KINA A Y,SOUZA V M,TAVARES S S M,et al. Microstructure and intergranular corrosion resistance evaluation of AISI 304 steel for high temperature service[J]. Materials Characterization,2008,59(5):651-655.
【5】HU C L,XIA S,LI H,et al. Improving the intergranular corrosion resistance of 304 stainless steel by grain boundary network control[J]. Corrosion Science,2011,53(5):1880-1886.
【6】王敏. 电阻焊在汽车工业中的应用[J]. 电焊机,2003,1:1-6.
【7】齐秀滨,刘娟,周军,等. 摩擦焊在我国石油钻杆制造中的应用[J]. 电焊机,2010(6):10-13.
【8】王树保,张海宽,冷雪松,等. 双钨极氩弧焊工艺及焊缝成形机理分析[J]. 焊接学报,2007(2):21-24,114.
【9】樊兆宝,梁养民. 时效不锈钢舱体的电子束焊与电阻点焊[J]. 电焊机,2007(3):23-27.
【10】闫晓锋. 真空电子束焊在我国航空机载设备上的应用及发展趋势[J]. 航空制造技术,2005(9):90-91,102.
【11】钟玉,屈金山,陈文静,等. TC4钛合金的电子束焊[J]. 热加工工艺,2007,36(15):24-26.
【12】张秉刚,吴林,冯吉才. 国内外电子束焊接技术研究现状[J]. 焊接,2004(2):5-8.
【13】FELBA J,FRIEDEL K P,KRUELL P,et al. Electron beam activated of cubic boron-nitride to tungsten carbide cutting tools[J]. Vacuum,2001,62:171-180.
【14】GOODMAN D L,BIRX D L,DAVE V R. High energy electron beam processing experiments with induction accelerators[J]. Nuclear Instruments and Methods in Physics Research,1995,99:775-779.
【15】蔡晖,贾建民,王亮. 国产超(超)临界锅炉构件常见问题及原因分析[J]. 华电技术,2008,4(30):27-31.
【16】张春雷. 某电厂Super304H钢管晶间腐蚀开裂原因分析[J]. 热力发电,2012,41(5):65-68.
【17】方可伟,刘飞华,李岩. EPR法在评价304L不锈钢晶间腐蚀敏感性中的应用[J]. 腐蚀与防护,2012,33(10):867-871.
【18】金维松,郎宇平,荣凡,等. EPR法评价奥氏体不锈钢晶间腐蚀敏感性的研究[J]. 中国腐蚀与防护学报,2007(1):54-59.
【19】陈睿,刘静,庞于忠. 1Cr18Ni9Ti不锈钢晶间腐蚀实验研究[J]. 河南冶金,2006,14(4):14-17.
【20】罗宏,龚敏. 奥氏体不锈钢的晶间腐蚀[J]. 腐蚀科学与防护技术,2006,18(5):357-360.
【2】张晶莹. 304奥氏体不锈钢晶间腐蚀的研究及防护[J]. 装备制造技术,2012(2):154-156.
【3】张春雷,陈亚庆. Super304H焊接接头晶间腐蚀性能的电化学动电位再活化法评价[J]. 广东电力,2015(3):1-4.
【4】KINA A Y,SOUZA V M,TAVARES S S M,et al. Microstructure and intergranular corrosion resistance evaluation of AISI 304 steel for high temperature service[J]. Materials Characterization,2008,59(5):651-655.
【5】HU C L,XIA S,LI H,et al. Improving the intergranular corrosion resistance of 304 stainless steel by grain boundary network control[J]. Corrosion Science,2011,53(5):1880-1886.
【6】王敏. 电阻焊在汽车工业中的应用[J]. 电焊机,2003,1:1-6.
【7】齐秀滨,刘娟,周军,等. 摩擦焊在我国石油钻杆制造中的应用[J]. 电焊机,2010(6):10-13.
【8】王树保,张海宽,冷雪松,等. 双钨极氩弧焊工艺及焊缝成形机理分析[J]. 焊接学报,2007(2):21-24,114.
【9】樊兆宝,梁养民. 时效不锈钢舱体的电子束焊与电阻点焊[J]. 电焊机,2007(3):23-27.
【10】闫晓锋. 真空电子束焊在我国航空机载设备上的应用及发展趋势[J]. 航空制造技术,2005(9):90-91,102.
【11】钟玉,屈金山,陈文静,等. TC4钛合金的电子束焊[J]. 热加工工艺,2007,36(15):24-26.
【12】张秉刚,吴林,冯吉才. 国内外电子束焊接技术研究现状[J]. 焊接,2004(2):5-8.
【13】FELBA J,FRIEDEL K P,KRUELL P,et al. Electron beam activated of cubic boron-nitride to tungsten carbide cutting tools[J]. Vacuum,2001,62:171-180.
【14】GOODMAN D L,BIRX D L,DAVE V R. High energy electron beam processing experiments with induction accelerators[J]. Nuclear Instruments and Methods in Physics Research,1995,99:775-779.
【15】蔡晖,贾建民,王亮. 国产超(超)临界锅炉构件常见问题及原因分析[J]. 华电技术,2008,4(30):27-31.
【16】张春雷. 某电厂Super304H钢管晶间腐蚀开裂原因分析[J]. 热力发电,2012,41(5):65-68.
【17】方可伟,刘飞华,李岩. EPR法在评价304L不锈钢晶间腐蚀敏感性中的应用[J]. 腐蚀与防护,2012,33(10):867-871.
【18】金维松,郎宇平,荣凡,等. EPR法评价奥氏体不锈钢晶间腐蚀敏感性的研究[J]. 中国腐蚀与防护学报,2007(1):54-59.
【19】陈睿,刘静,庞于忠. 1Cr18Ni9Ti不锈钢晶间腐蚀实验研究[J]. 河南冶金,2006,14(4):14-17.
【20】罗宏,龚敏. 奥氏体不锈钢的晶间腐蚀[J]. 腐蚀科学与防护技术,2006,18(5):357-360.
相关信息